499507
30
Zoom out
Zoom in
Previous page
1/44
Next page
- 30 -
0DT829 15/10/2012

49E
17 14 12 11 0 0 0 1 1 2 3 4 6 8 9 20 41
17 14 12 11 0 0 0 1 1 2 3 4 6 8 9 20 41
INPUTS
Command Function Description
1 2
N.O
Automatic closing
Permanently closing the contact enables automatic closing.
1 3 N.O
Opening
With DIP1=ON the closure of the contact activates an opening operation.
Step-by-step
With DIP1=OFF the closure of the contact activates an opening or closing
operation in the following sequence: open-stop-close-open.
Note: if automatic closing is enabled, the stop is not permanent but at a
time that is set by the TC.
1 4
N.O
Closing
The closing manoeuvre starts when the contact is closed.
1 6 N.C
Reversal safety
device
Opening the safety contact triggers a reversal of the movement (reopening)
during a closing operation.
41 8 N.C
Reversal safety
device
Opening the safety contact triggers a reversal of the movement (reopening)
during a closing operation.
1 9 N.C
Stop
Opening the safety contact stops the current operation.
1 9 N.O
Non-pulse command
Permanently opening the safety contact enables the operation by non-
pulse command.
In this state, the opening (1-3/1-20) and closing (1-4) controls function only
if held in the pressed position, and the automation stops when the controls
are released.
All safety switches, the step-by-step control and the automatic closing
function are disabled.
1 20 N.O
Partial opening
The closing of the contact activates a partial opening operation of the
duration set with the RP trimmer.
Once the automation stops, the partial opening control performs the
opposite operation to the one performed before stoppage.
0 11
N.C
Closure limit switch
The opening of the limit switch contact stops the closure operation.
0 12
N.C
Opening limit switch
The opening of the limit switch contact stops the opening operation.
0 17
Do not use
Leave the input not connected

Operation by non-pulse command Operation by pulse command
OUTPUTS
Card Output Value Description
EL07L
1 +
0
24 V= / 0,5 A
Accessories power supply.
Power supply output for external accessories, including
automation status lamp.
0 14
24V= / 50 W
(2 A)
Flashing light (LAMPH).
Activated during opening and closing operations.
EL07PW1
- LK + 24 V= / 0,5 A Output activated during the door running.
400 V~ / 4 A

Note: if the direction of rotation of the motor is incorrect for the
desired direction of movement, swap the U - W phases.
U W V
M
3 ~
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DITEC Traffic CM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DITEC Traffic CM in the language / languages: English, Dutch as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info