798246

Dimplex WI 65TU Manual

21
Zoom out
Zoom in
Previous page
1/68
Next page
www.gdts.one 452237.66.51 · FD 9912 EN-3
WI 65TU - WI 95TU English
1.4 Energy-efficient use of the heat
pump
By operating this heat pump you are helping to protect our en-
vironment. Both the heating system and the heat source must
be properly designed and dimensioned to ensure efficient op-
eration. It is particularly important to keep water flow tempera-
tures as low as possible. All connected heat consumers should
therefore be suitable for low flow temperatures. Raising the
heating water temperature by 1 K corresponds to an increase in
electricity consumption of approx. 2.5 %. Low-temperature
heating systems with flow temperatures between 30 °C and
50 °C are particularly well-suited for energy-efficient operation.
2 Intended use of the heat
pump
2.1 Intended purpose
The water-to-water heat pump is to be used exclusively for the
heating of heating water. It can be used in newly built or previ-
ously existing heating systems. Water is used as the heat car-
rier. It can be supplied by wells or other water systems.
In order to eliminate the risk of corrosion at the evaporator, the
well water must be evaluated regarding the corrosion behaviour
of metallic materials according to DIN 50930.
Details can be found in the project planning and installation
manual for heat pumps for heating purposes.
ATTENTION!
!
!
The well water must comply with the required water quality
standards.
(see Cap. 9.4 on pag. 10)
2.2 Operating principle
A well pump conveys the water to the evaporator of the heat
pump. There the heat is transferred to the refrigerant in the re-
frigerating circuit.
The refrigerant is drawn in by the electrically driven compres-
sor, compressed and "pumped" to a higher temperature level.
The electrical power needed to run the compressor is not lost in
this process. Most of it is absorbed by the refrigerant.
The refrigerant subsequently passes through the liquifier where
it transfers its thermal energy to the heating water. Depending
on the set operating point, the heating water can thus be
heated up to a max. of 62 °C.
3Basic device
The device consists of a heat pump for indoor installation wired
ready for use with metal casing, switch box and integrated heat
pump manager. The refrigeration circuit is "hermetically sealed"
and contains the fluorinated refrigerant R410A included in the
Kyoto protocol. Information on the GWP value and CO2 equiva-
lent of the refrigerant can be found in the chapter Device infor-
mation. The refrigerant is CFC-free, non-ozone depleting and
non-combustible.
All components required for the operation of the heat pump are
located in the switch box. An outside temperature sensor in-
cluding fixing accessories and a dirt trap are supplied with the
heat pump. The supply for the supply voltage and the control
voltage must be installed by the customer.
The circulating pumps included in the scope of supply must be
installed in accordance with the hydraulic diagrams (see Cap. 4
on pag. XIV) or the development documents. The electrical con-
nection of the circulating pumps must be established in ac-
cordance with Cap. 7.5.3 on pag. 9.
The control wire of the primary pump (to be provided by the
customer) is to be connected to the control box. When so do-
ing, a motor protecting device is to be installed, if required.
The customer must provide hydraulic components for the well
water circuit.
1) Switch box
2) Evaporator
3) Liquefier
4) Filter dryer
5) Compressor 1
6) Compressor 2
7) Expansion valve
8) Economiser
3
8
2
4
1
7
5
6
WI 65TU
1
2
8
3
5
6
7
4
WI 95TU
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex WI 65TU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex WI 65TU in the language / languages: English, German, French as an attachment in your email.

The manual is 2.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info