798190
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
Fitting panel – After Installation
The Back Panel can also be change after the product has been installed, a person of suitable
competency is required to carry out this task. Please follow the steps below.
1. Unplug product from Power Supply and remove front trim on unit. See Fig. 2
2. Remove Front Glass from product and store in a safe place. (A suction cup is provided to help
remove/place the front glass.) See Fig. 6
3. Remove Fuelbed fixing screws, then remove Fuelbed. (Fig. 7)
4. Remove both Side Glasses by moving them out at the bottom, then sliding out to remove. Store
these in a safe place. (Fig. 8).
5. Remove plastic Inner Screen by tilting it from the base. (Fig.9)
6. Remove Back Inner Panel bracket (Fig. 10A), Inner Back panel can then be tilted and removed
from its housing. (Fig. 10B)
7. Replace with new Back Inner Panel, and reverse the steps set out above, to re-assemble the
product. Ensure Inner screen is reassembled correctly. (Smooth mirrored finish to face the front of
the product.)
Step 3: Installing the Product
CAUTION: Two people will be required for various steps of this procedure.
This product is designed to be installed into existing block wall or a custom-built studded wall
structure. Please consult a competent installer before undertaking this to ensure a safe and
secure installation. If installing into an existing chimney or flue, please ensure that the chimney or
flue is blocked o. This is to prevent up-draughts aecting product operation.
Electrical Requirements
NOTE: A dedicated, properly fused 13 Amp circuit is required, rated for the appropriate voltage
(230-240V). An isolation switch should also be incorporated in cases where the product plug is
inaccessible after installation.
WARNING: Construction and wiring must comply with local building codes and other applicable
regulations to reduce the risk of fire, electric shock and injury to persons.
WARNING: To reduce the risk of fire, electric shock or injury to persons, always use a licensed
electrician.
1. Using the product dimensions (Fig. 11), build a suitable structure for the product to fit into.
Ensure that, when installed, the product is within 1m of a power outlet. Please refer to Electrical
Requirements section above for more details.
It is recommended that the base of the unit is installed between 200mm and 800mm from the
floor. This is to maintain an optimised viewing angle of the fire eect. (See Fig. 12)
The product must not bear the weight of the finished wall located above it. Consider the use of a
lintel for appropriate support.
2.Using any combination of the three fixing methods (Fig. 13 a,b,c), fix the product to its supporting
structure.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex Vivente VVT75 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex Vivente VVT75 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2.16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dimplex Vivente VVT75

Dimplex Vivente VVT75 User Manual - Dutch, Danish, Polish, Turkish, Norwegian - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info