798446

Dimplex SI 85TUR Manual

24
Zoom out
Zoom in
Previous page
1/64
Next page
EN-6 452237.66.56 · FD 9912 www.gdts.one
English SI 85 TUR
7 Assembly
7.1 General
The following connections need to be established on the heat
pump:
Flow and return of the brine (heat source system)
Assembly of the hydraulic 4-way reversing valve Y12
with the double nipples (2½“) provided, all connections on
the heat pump can also be used as external thread seal-
ing
Flow/return heating to the hydraulic 4-way reversing valve
Power supply
Temperature sensor
7.2 Assembling the hydraulic 4-way
reversing valve
7.2.1 Assembly preparation SI 85TUR
Fig. 7.1:
The hydraulic 4-way reversing valve (6) preassembled with the
actuator is fixed on a transport plate (7) inside the unit with its
threaded flanges (see Fig. 7.1 on page 6). After dismantling the
hydraulic 4-way reversing valve from the device compartment,
the transport plate (7) must be removed. The threaded flanges
of the 4-way reversing valve must be loosened. The connec-
tions elements and the flange gaskets are placed, together with
the protective filter in the accessory box (8), on the plate heat
exchanger. Two preassembled pipe assemblies (9) are placed
on the baseplate of the heat pump. These pipe assemblies must
be connected with the threaded flanges as shown in Fig. 7.2 on
page 6.
7.2.2 Assembly
Fig. 7.2:
The clearances shown in Fig. 7.2 on page 6 must be achieved
with the sealing process between the double nipple and
threaded flange on the heat pump on the one hand, and be-
tween the "heating water flow" pipe assembly and threaded
flange on the other. When the required installation position is
achieved, the flanges with the accompanying seals must be
connected with the hydraulic 4-way reversing valve using
screws, washers and spring washers.
The hydraulic 4-way reversing valve can be mounted in the four
positions shown Fig. 7.3 on page 7 to Fig. 7.6 on page 7. The
correct position of the motor control lever is pointed out again
in detail according to its installation position and depending on
the operating mode (heating or cooling).
7
9
6
8
55
485
194
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex SI 85TUR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SI 85TUR in the language / languages: English, German, French as an attachment in your email.

The manual is 5.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info