798446
22
Zoom out
Zoom in
Previous page
1/64
Next page
EN-4 452237.66.56 · FD 9912 www.gdts.one
English SI 85 TUR
3 Scope for Delivery
3.1 Basic device
The basic device consists of a ready-to-use heat pump for in-
door installation, complete with sheet metal casing, control
panel and integrated heat pump manager. The refrigerant cir-
cuit is hermetically sealed. It contains the Kyoto protocol ap-
proved refrigerant R410A with a GWP value of 2088. It is CFC-
free, does not deplete ozone and is non-flammable.
All components required for the operation of the heat pump are
located in the control box. An external temperature sensor in-
cluding fixing accessories, a dirt trap and a flow rate switch, is
supplied with the heat pump. The supply for the load current
and the control voltage must be installed by the customer.
The circulating pumps (brine and heating water side) included in
the scope of supply must be installed in accordance with the hy-
draulic diagrams (see cap. 3 on page VIII) or the development
documents. The electrical connection of the circulating pumps
must be established in accordance with Cap. 7.6.3 on page 11.
Both the heat source system and the brine circuit manifold
must be provided on-site.
1) Switch box
2) Evaporator
3) Liquefier
4) Compressor 1
5) Compressor 2
6) Expansion valve
3.2 Accessories pack
1x dirt trap 2½“ DN65 for the heat source side
1x hydraulic 4-way reversing valve DN 65 with actuator +
connection cable mounted
4x threaded flange 2
4x flange gasket 2½“
16x screws M12 x 50
16x washers 13 DIN 125
Annular spring 12.2 DIN 127
16x nut M12
2x double nipples 2½“
1x assembly and usage instructions user
1x assembly and usage instructions technician
1x pipe assembly heating water flow
1x pipe assembly heating water return
1x external sensor
4 Accessories
4.1 Connecting Flanges
The device can optionally be switched to flange connection
using the flat-sealing connection flange.
4.2 Remote control
A remote control adds convenience and is available as a special
accessory. Operation and menu navigation are identical to
those of the heat pump manager. Connection takes place via an
interface (special accessories) with RJ 12 Western plug.
NOTE
º
In the case of heating controllers with a removable operating
element, this can also be used directly as a remote control.
4.3 Building management
technology
The heat pump manager can be connected to a building man-
agement system network via supplementation of the relevant
interface plug-in card. The supplementary installation instruc-
tions of the interface card must be consulted regarding the
exact connection and parameterisation of the interface.
The following network connections can be made on the heat
pump manager:
Modbus
EIB, KNX
Ethernet
ATTENTION!
!
!
If the heat pump or circulating pump is controlled externally,
an flow rate switch is required to prevent the compressor
from being switched on when there is no volume flow.
1
2
3
4
5
6
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex SI 85TUR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SI 85TUR in the language / languages: English, German, French as an attachment in your email.

The manual is 5.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info