Manual Dimplex HPL 6S-TUW2 (page 24 of 52) (English, German, French)

798227

Zoom out

Zoom in

1/52

EN-8 452163.66.69 · FD 0010 www.glendimplex.de

English HPL 6S-TUW2

7.3 Electrical connection

A standard five-core cable is used for connecting the heat

pump to the power supply.

The cable must be provided by the customer. The conductor

cross section is selected in accordance with the power con-

sumption of the heat pump (see appendix Device information)

and the applicable VDE (EN) and VNB regulations.

An all-pole disconnecting device with a contact gap of at least

3 mm (e.g. utility blocking contactor or power contactor) as well

as a 3-pole circuit breaker with common tripping for all external

conductors must be installed in the power supply (tripping cur-

rent in compliance with the device information).

The relevant components in the heat pump contain an internal

overload protection.

When connecting, ensure that the incoming supply has a clock-

wise rotating field.

Phase sequence: L1, L2, L3.

ATTENTION!

Ensure the rotary field is clockwise when connecting the

mains cables (if the rotary field is not clockwise, the heat

pump will not work properly, is very loud and may cause

damage to the compressor).

The control voltage is supplied via the heat pump manager.

A 3-pole line must be laid for this in accordance with the

electrical documentation. Further information on the wir-

ing of the heat pump manager is available in the heat pump

manager operating instructions.

A shielded communication line (J-Y(ST)Y ..LG) (not included

in the scope of supply) connects the heat pump manager

with the WPIO controller installed in the heat pump. More

detailed instructions can be found in the heat pump man-

ager operating instructions and in the electrical documen-

tation.

ATTENTION!

The communication cable is necessary for the function of air-

to-water heat pumps in outdoor installation. It must be

shielded and laid separately from the mains cable

7.3.1 Demand sensor connection

The demand sensor R2.2 is included with the heat pump man-

ager. It must be connected (Cap. 3.2 on page VI).

NOTE

The return sensor R2 installed in the heat pump is active when

the compressor is running and must not be disconnected

8 Commissioning

8.1 General

To ensure that commissioning is performed correctly, it should

only be carried out by an after-sales service technician author-

ised by the manufacturer. This may be a condition for an addi-

tional warranty (see "Warranty service").

8.2 Preparation

The following items must be checked prior to commissioning:

All of the heat pump connections must be installed as de-

scribed in Chapter 7.

All valves which could impair the proper flow of the heating

water in the heating circuit must be open.

The air intake and air outlet paths must be clear.

The fan must turn in the direction indicated by the arrow.

The settings of the heat pump manager must be adapted

to the heating system in accordance with the latter's op-

erating instructions.

Ensure that the condensate drain functions properly.

8.3 Procedure

The heat pump is commissioned via the heat pump manager.

Settings should be made in compliance with the HPM's instruc-

tions.

At heating water temperatures below 7 °C, commissioning is

not possible. The water in the buffer tank must be heated with

the second heat generator to at least 18 °C.

To ensure problem-free commissioning, the following proce-

dure is to be implemented:

1) Close all consumer circuits.

2) Ensure that the heat pump has the correct water flow.

3) Use the manager to select the automatic operating mode.

4) In the special functions menu, start the "Commissioning"

program.

5) Wait until a return temperature of at least 25 °C has been

reached.

6) Now slowly reopen the heating circuit valves in succession

so that the heating water flow rate is constantly raised by

slightly opening the respective heating circuit. The heat-

ing water temperature in the buffer tank must not be al-

lowed to drop below 20 °C during this process. This en-

sures that the heat pump can be defrosted at any time.

7) When all heating circuits are fully open and a return tem-

perature of at least 18 °C is maintained, the commissioning

is complete.

ATTENTION!

Operating the heat pump at low system temperatures may

cause the heat pump to break down completely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex HPL 6S-TUW2 in the language / languages: English, German, French as an attachment in your email.

The manual is 2.2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex HPL 6S-TUW2 Manual

Product: