798061
10
Zoom out
Zoom in
Previous page
1/24
Next page
4.5.1.4 - Connection to the photovoltaic function (PV)
This function enables the
appliance to operate in auto-
production mode, which
means that it will use the
energy produced by the PV
function to supply the heat
pump as well as the electrical
back-up, and to heat the water
in the tank.
The connection is made
between the energy manager
electrical box (not supplied)
and connectors 1 and 2 on the electronics board.
• Remove the protective casing.
• Remove the black cover from the electronics board.
• Connect the PV function cable to connector 1 on the electronics board.
• If the PV function regulator has two control contacts, connect them to connectors 1 and
2 on the electronics board. See § « Electrical box electrical diagram » in the appendix. .
Terminal 1: a low level of electrical energy is produced by the PV function.
Terminal 2: a high level of electrical energy is produced by the PV function.
CAUTION: Connectors 1 and 2 are for DRY CONTACTS ONLY. They must NEVER be connected to 230V.
Deterioration risk: the water tank must be
lled before the appliance is switched on
or connected to a power supply.
5.1 - Control panel
5 - SET-UP AND USE
• Leave the appliance unplugged.
• Open the hot water outlet which is located the highest on the
appliance.
• Open the cold water inlet on the pressure-relief valve.
• Fill the tank until water is coming out of the highest outlet.
• Close the hot water outlet.
Before turning the appliance on, ensure that the entire circuit is
watertight.
The heat pump water heater operates primarily with the
heat pump as long as the air intake temperature remains in
the authorised range from -7°C à +35°C. Outside of this range, the
electrical back-up ensures the heating of domestic hot water.
The temperature of the domestic hot water provided by the heat
pump is adjustable up to 60°C.
In the case of high domestic hot water consumption, the heat
pump water heater has a comfort function, t°C mini which
increases the heating capacity when there is less than 1/3 of
the tank’s volume left at over 38°C (see § «t°c mini -minimum
temperature-»). There is also a setting to activate the electrical
back-up if the heating time is too long (see § « max time»).
If more domestic hot water is required from time to time, the heat
pump water heater has a « boost» function (activated by the user)
which ensures that the water heats to the desired temperature
(
for example : 50°C
) quickly with the help of the heat pump and
electrical back-up, This function is deactivated as soon
as the required temperature is reached.
From time to time, check that there are no alerts (in case of an
alert, please refer to § «Error messages»).
..... Compressor activated
..... Fan activated
........ Defrosting in progress
........ Electrical back-up
activated
.... Domestic hot water
requested
.... Comfort mode in
progress
....... Eco mode in progress
....... Freeze protection mode
in progress
...... Holiday mode in progress
..... Keyboard locked
......... Settings/parameters
being displayed
.... PV mode activated
1 2 3...7. Date
Pictograms:
- INSTALLER HEAT PUMP WATER HEATER 200 -270L AIR D/2 - MANUAL-
10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex Edel 200 AIR D-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex Edel 200 AIR D-2 in the language / languages: English as an attachment in your email.

The manual is 2.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dimplex Edel 200 AIR D-2

Dimplex Edel 200 AIR D-2 User Manual - Dutch - 48 pages

Dimplex Edel 200 AIR D-2 Installation Guide - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info