520634

Dimplex DEE 2103 Manual

14
Zoom out
Zoom in
Previous page
1/38
Next page
8
EN
Installation instructions
Install the continuous-flow heater as described in the
illustrated section. Observe the instructions in the text.
Safety information
Risk of electric shock!
Switch off the mains voltage supply immediately if
a fault occurs.
We do not accept liability for damage resulting from
■
failure to heed these instructions.
The continuous-flow heater may only be connected
■
and put into operation by a qualified professional.
Never open the appliance without disconnecting the
■
power supply beforehand.
The statutory regulations of the respective country, as
■
well as those of the local electricity and water suppliers,
must be adhered to.
The continuous-flow heater is a Class
■ I appliance and
must be connected to the protective earth.
The appliance must be permanently connected to in-
■
stalled pipes. The conductor cross-section must comply
with the installed appliance power.
Caution
■ : Earthed water pipes may give the appearance of
a connected protective earth.
To guarantee compliance to relevant safety regulations,
■
an all-pole separator must be fitted during installation.
The contact opening must be at least 3 mm.
The continuous-flow heater is only suitable for closed
■
(pressurized) operation.
The tap and outlet fittings must be approved for operation
■
with closed (pressurized) continuous-flow heater systems.
The continuous-flow heater can be operated with cold or
■
pre-warmed water (for example, from a solar energy unit
water supply). Observe the technical data and the special
accessories for this purpose.
Only connect the continuous-flow heater to a cold water
■
line.
The continuous-flow heater may only be installed in a
■
frost-free room.
Disconnect the electrical connection cable from the
■
supply and shut off the water supply before connect-
ing the appliance!
Connect the water supply and then connect the elec-
■
trical supply.
Only make the openings which are required for instal-
■
lation on the rear of the appliance. If the appliance is
reinstalled, the unused openings must be provided with
watertight sealing.
Do not touch electrically live parts after installation.
■
Installation
I.
Unpacking/Removing the cover
Unpack the appliance and check for transport-related ■
damage.
Please dispose of the packaging, and if applicable, the old
■
appliance in an environmentally-friendly manner.
II.
Preparations for installation
Important: Only use the supplied installation set.
The supplied water connection nozzles must be installed!
Shut off water supply. The electrical connection (connec-
■
tion cable) must be disconnected from the power supply.
Unscrew the fuse or switch off the circuit breaker.
III.
Wall mounting
The continuous-flow heater must be mounted on the ■
wall. Attach it if necessary on the lower adjustable screws.
The distance to the wall is variable. You can compensate
■
for any unevenness of the wall's surface.
The grommet must tightly surround the connection cable.
■
If it is damaged during mounting, the openings must be
provided with watertight sealing.
IV.
Water connection
The continuous-flow heater must be vented. The ■
warm water tap must be opened and the appliance
must be flushed out thoroughly for 1 minute with
at least 6 litres of water.
V.
Electrical connection/Mounting
The electrical supply terminal can be fitted at the top or ■
bottom. The sheath of the connection cable must extend
for at least 40 mm into the appliance.
VI.
Startup/additional information
First start-up
Switch on the fuses.
■
Setting the temperature. ■
Starts rinsing: Open the warm water tap and allow water ■
to flow for at least 1 minute (flow-rate at least 6 litres per
minute). Only then (for safety reasons) will the appliance
begin to heat.
Tip: Should the appliance not start because of a reduced
flow-rate, remove the perlator, shower head or similar before
start and repeat the process.
Remove the flow-rate limiter (see Fig. A) with low water
■
pressure.
Explain the operation of the continuous-flow heater to
■
the user.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex DEE 2103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex DEE 2103 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info