706442

Dimplex CAS250 Manual

8
Zoom out
Zoom in
Previous page
1/35
Next page
Operating the Product
This section describes how to activate your re using either the manual controls or remote control. Inert the mains
plug to the socket outlet (ensure that the supply voltage matches the voltage marked on the appliance).
MANUAL CONTROLS
The manual controls are located beneath the metal bed - see Fig. 11 for Manual Control lay out.
Switch ‘A’:- Controls the electricity supply from the power supply unit to the Fire.
Note: This switch must be in the ‘ON’ ( I ) position for the Fire to operate.
BLUE TOOTH (BT) RECEIVER
Button ‘B’:- Press once to turn on the ame effect. The LED’s light up - it will take a further 45 seconds before the
ame effect starts.
(Button ‘C’ is used to pair the remote control - see Blue Tooth Remote Control section below)
Press to put re in to standby mode. This will be indicated by the LED’s switched off.
Button ‘D’and ‘E’:- Control the intensity of the ame effect.
Press button ‘D’ to decrease the ame height.
Press button ‘E’ to increase the ame height.
When ame height reaches max. or min. the LED’s will blink once.
Give the ame generator a couple of seconds to react to changes you may make.
The appliance will use less water if the ame effect is set to a lower level.
The Blue Tooth receiver can be removed from its location and placed outside the product if preferred. To do this,
remove the metal bed - see Fig. 3, remove the Air lter - Unclip the BT receiver and feed it out through the air lter
inlet hole - see Fig. 12. Unwind the cable from underneath and t the BT receiver where desirable (cable length from
inlet hole is 120cm). Replace the lter and the metal bed.
BLUE TOOTH (BT) REMOTE CONTROL
The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
- see Fig. 13 and after removing the batteries from the plastic wrapping t them into place. Replace the battery cover.
The remote control has wireless technology and is required to be paired to the receiver. This is done by pressing the
button (C) on the BT receiver. The LED’s will start to blink on and off. This is to let you know that the appliance is ready
to connect to the remote control. Press the button (B) on the remote control. The appliance will switch off. Now the
remote control is paired to the appliance.
The operation of the remote control is the same as described in ‘Receiver Controls’.
There are 3 buttons on the remote control - see Fig. 14. To operate correctly the remote must be pointed towards the
product. The remote control functions operate in the same way as the manual buttons ‘B’, ‘D’ and ‘E’.
Standby (B)
Flame down (D)
Flame up (E)
Maintenance
GENERAL TIPS
Only use decalcied/ltered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
The appliance should never be operated if the LED’s are not working.
FILLING THE WATER TANK
When the water tank needs relling, the LED’s, ame/smoke effect shuts off. (To indicate when tank needs relling,
the LED’s blink twice, approximately 15 minutes before the ame/smoke shuts off)
1. Lift out the metal bed and place carefully on the table/worktop - see Fig. 3.
2. Remove the water tank by lifting upwards and outwards - see Fig. 6.
3. Place the water tank in sink and remove cap, anti-clockwise to open - see Fig. 9.
4. Fill tank with decalcied/ltered water only. This is necessary to prolong the life of the ame and smoke
producing unit.
The water should be ltered through a conventional domestic water lter unit and the lter should be replaced
regularly.
5. Screw the cap back on (clockwise), do not over tighten.
3
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex CAS250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex CAS250 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info