706337

Dimplex CAS 1000R Manual

12
Zoom out
Zoom in
Previous page
1/56
Next page
4
This section describes how to activate your re using either the manual controls or remote control.
MANUAL CONTROLS
The manual controls are located beneath the fuel bed. (Fig 21)
CAS500R
Mains Switch - Controls the electricity supply to the appliance. (Fig 21A)
Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate
Button Panel - Controls the functioning of the appliance. (Fig 21B)
• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by a single
beep and the main LED lights activating. Be careful not to look directly into the LED’s as they can be very bright.
Although the main LED lights operate immediately, a further 45 seconds of warm up time is required before the
ame effect starts.
• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details.
• is the test mode button. This will be used by the manufacturer and the Service Engineer.
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level.
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level.
• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off. You will hear an audible beep when you reach the minimum level
• is the increase re crackling sound. Press this to increase the volume of the crackling sound.You will hear an
audible beep when you reach the maximum level.
CAS1000R
Mains Switch - Controls the electricity supply to the appliance. (Fig 21A)
Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate
Button Panel ‘C’ Controls the functioning of the left side of product while Button Panel ’D’ controls the functioning of the
right side of the product. Please note the ame height and re crackling noise can be controlled independently on each
individual side of the product.
• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by a single
beep and the main LED lights activating. Be careful not to look directly into the LED’s as they can be very bright.
Although the main LED lights operate immediately, a further 45 seconds of warm up time is required before the
ame effect starts.
• is the pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details.
• is the test mode button. This will be used by the manufacturer and the Service Engineer.
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level.
• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off. You will hear an audible beep when you reach the minimum level.
• is the increase re crackling sound. Press this to increase the volume of the crackling sound. You will hear an
audible beep when you reach the maximum level.
Operating the Product
Multiple Product Installation
Follow steps 1-4 in “Installing the Product into Surround/Enclosure” to t the rst product. It is important that the rst
product is orientated so that the side of the product with the slots is left free and not connected to rst end of the
installation (Fig 18).
1. When the rst product is installed and securely xed, prepare the second product by unscrewing the joining screws
(Fig 19A) and screwing them into the opposite side of the metalwork (Fig 19B). Please note, these screws should
not be fully tightened and 5-10mm of thread should be left protruding from the edge of the product.
2. Fit the second product beside the rst product, ensuring the protruding screws of the second product engage with
slots of the rst product. (Fig 20)
3. Ensure the second product is at the correct height to match the rst product and ensure it is adequately level. This
can be done by adjusting the adjustable feet with a at head screwdriver. (Fig 8) The levelness of the product can
be veried by checking the on-board level (Fig 9)
4. Tighten the screws of the second product so that it joins tightly with the rst product.
Additional products can be tted to the second product by following steps 1-4 above.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex CAS 1000R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex CAS 1000R in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 10,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info