695367

Dik Geurts Vision 100 Manual

24
Zoom out
Zoom in
Previous page
1/64
Next page
English
USER MANUAL
5. Burning instructions and tips
Below you will find tips and instructions that are important for a good operation of your fire.
5.1 Fuel
Good fuel is the ‘engine’ of your fire. You will benefit the most from your fire, if you burn it with high quality, well
dried wood or wood briquettes. In this way you will prevent unwanted additional effects like excess smoke
formation as a result of poor combustion, insufficient heat yield and poor efficiency. The fire is only suitable to be
filled with clean wood or wood briquettes.
Wood is usually purchased in cubic metres. However, there are many types of ‘cubes’ available on the market:
• A genuine cube (neatly stacked sawn and split wood): 1.0 m
3
(approx. 700 kg).
• A bulk cube (wood loaded in 1 m3 trays): 0.6 m
3
(approx. 400 kg).
• A stere (neatly stacked one metre sections): 1.3 m
3
(approx. 900 kg).
Dry wood
Wood must be properly dry. Freshly felled wood is not suitable, as it contains too much moist (approx.
60%). Oven-dried wood, on the other hand, is suitable. Therefore, you should allow the wood to dry for at least one
year, and preferably for two to three years. The wood will dry if you store it outside under a lean-to (i.e. not in the
garage), preferably in a sunny location. This will allow the wind (but not the rain) to get to it. Short, split stems will
dry the quickest. After drying, they only contain 15 to 20% moist and will provide the highest output.
!Tip
Dry wood will generate a bright sound when you hit two blocks together. At the front side there will be shrinkage
cracks and the bark will come loose easily.
We recommend using a moisture gauge to measure the moist percentage of the burning wood. It will be available
at your supplier.
In order to determine the moist percentage correctly, please pay attention to the following:
• First allow the burning wood to reach room temperature.
• Always measure in the core of the wood block.
• This is why you should always cleave a wood block through the middle first.
• Press the moisture gauge's measuring pinsdiagonally on the grain,uprightandfirmly in the middle of the
freshly cleaved surface.
There is no point in measuring at the cross-cut of the wood or parallel to the grain.
• The measurement provides an indication. In order to get a more accurate picture, the measurement should be
repeated on several places (and perhaps on various wood blocks).
• The burning wood may have a maximum moist percentage of 20%. If the wood is too dry, i.e. below a moist
percentage of 10%, it will quickly gasify and overloading could occur, particularly in the case of lighter wood
types.
5.1.1 Amount of wood
You must observe the recommended volume of wood blocks (number AND dimensions) provided in Appendix 1,
Table 2. When a larger volume is used, the heat delivery will increase. In that case, the fire could get overloaded, as a
result of which parts could get damaged and/or the walls of the fire will discolour. The glass pane could also
blacken sooner. If the fire is burning too hard, you should use coarser/harder wood.
Always heat the appliance to capacity. Gross, 1 kg of dry burning wood will supply approx. 4 kWh (kilowatt hour) of
energy. For example: for an appliance with a capacity of 4-8 kWh, you must add 1-2 kg of firewood every 45
minutes.
The capacity of your fire can be seen in the installation manual in appendix 2 and on the data plate.
5.1.2 Suitable types of wood
The following types of wood are recommended for burning your fire:
• Hard types of wood such as oak, beech, hornbeam, ash and fruit tree wood. These types of wood generate a
short flame and will burn longer.
• Light types of wood such as birch, poplar, willow and alder. These types generate a long flame but burn up
rather quickly.
• Wood briquettes (compressed wood chips) are not to be burnt in a smoke control area.
!Caution
Coniferous or pine wood. This wood should only be used in a well burning fire, because otherwise you will get
deposits in the flue duct. It is not really suitable for open fires, because of the sparks. Pine is often used as kindling
wood.
UK
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Vision 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Vision 100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info