Manual Dik Geurts Vision 100 (page 22 of 64) (English, German, Dutch, French)

695367

Zoom out

Zoom in

1/64

English

USER MANUAL

4. Lighting and burning

4.1 Instructions

Observe the following instructions for a good and safe operation of your fire:

!CAUTION

Have your flue duct checked by a recognized specialist for blockage and contamination if you have not burned the

fire for some time.

!CAUTION

• Have the flue duct inspected and cleaned by a specialist at least once or twice per year. The flue duct must be

clean and function properly for your fire to be used safely and without any problems.

• use the right fuel only (see section 5.1);

• observe the maximum amount of wood blocks as stated in Appendix 1, Tabel 2;

• make sure that sufficient fresh air is supplied (see section 5.2);

• in case of a fire in the chimney, close the air supply, extinguish the wood fire with sand and call the fire

brigade;

• never extinguish the wood fire with water;

• do not clean the fire with a vacuum cleaner (see section 5.4).

!Caution

• preferably, do not burn the fire during misty and/or windless weather in order to prevent (smoke) nuisance;

• burn a fire with the door closed. It is only opened to fill additional wood;

• a properly heated flue duct is necessary for the draught in the duct;

• a high combustion temperature will keep the flue duct clean.

4.2 Lighting

Observe the following steps for lighting and burning your fire:

If necessary, remove a part of the ash with the supplied ash scoop (see section 5.4).

If necessary, clean the glass pane (see section 6.6).

If applicable, open the flue valve.

Fully open the air supply using the air supply slide (with indication closed/open, see Appendix 2, Fig. 3a and 3b);

Place 2 small wood blocks in the combustion chamber, lengthwise (see Appendix 2, Fig. 4);

Stack kindlings crosswise on the 2 wood blocks and place a firelighter on top of it (see Appendix 2, Fig. 5).

Make sure that sufficient air is able to flow through the stack of wood, so that the wood will easily ignite.

Light the firelighter and, if applicable, a ball of paper.

Close the fire door, it may be left open a little bit, if necessary, until the kindlings have caught fire.

Allow the fire to burn through properly in order to heat up the flue duct. In this way, a good draught is created.

To keep the glass pane clean, allow the fire to burn hot until it burns out.

!Caution

• do not place a wood block diagonal in front of the air supply;

• do not start with large wood blocks, build up the fire calmly;

4.3 Burning

Allow the fire to continue burning on small wood blocks until a properly burning fire is created with a glowing

ember bed.

In case of a wide fire: now distribute the glowing fire bed over the fire's width and place a few more small wood

blocks on top of it.

Control the output with the air supply slide only after approx. 15-20 minutes when there is a properly burning fire

with ember bed. Simply allow the appliance to continue burning using the air supply slide.

Then fill the fire with larger wood blocks (see table 2 in Appendix 1 for the amount) after the small wood blocks

have been burnt for a large part.

If necessary, further open the air supply slide for a moment, to allow the fire to burn properly again.

!CAUTION

Make sure that wood blocks do not fall/lie against the glass pane.

!CAUTION

For good combustion and optimal ease of use, always heat the appliance to capacity.

!Tip

• Carefully pace the wood blocks in the fire in order to prevent the inner lining from getting damaged.

Be particularly cautious in case of wood stems with side branches;

• Place the wood blocks loosely on top of each other and make sure they can be reached by sufficient air;

• If the fire is not burning properly, you can temporarily open the air supply slide further;

• Do not only use soft wood, but mix it with hard wood in particular.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Vision 100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dik Geurts Vision 100 Manual

Product: