695347

Dik Geurts Instyle 800V Manual

42
Zoom out
Zoom in
Previous page
1/112
Next page
English
INSTALLATION MANUAL
9.5 Frames
The appliances can be fitted with various frames. The frames are adjustable in depth and can be fitted so they are
parallel to the door.
!Caution
The installation depth of the appliance depends on the selected frame (see Annex 2, fig. 1)!
When assembling the frame proceed as follows:
Tip!
First remove the door before assembling the frame.
In-built frame (no frame):
Ø
Remove the 4 pre-assembled bolts/nuts (see Appendix 2, Fig. 11).
Ø
Slide the frame over the stove into the desired position (see Appendix 2, Fig. 12).
Ø
Fasten the 4 bolts and nuts (the bolts on the inside, the nuts on the outside of the appliance)
(see Appendix 2, Fig. 13).
Ø
Fasten the 2 bolts and nuts on top of the appliance (see Appendix 2, Fig. 13).
Other frames:
Ø
Loosen the 4 pre-assembled bolts (see Appendix 2, Fig. 14).
Ø
Slide the frame in the convection casing between the loosened bolts and the bolts still tight in the appliance
(see Appendix 2, Fig. 15).
Ø
Tighten the nuts. The frame is now clamped between the nuts (see Appendix 2, Fig. 16).
9.6 Adjustable feet
In order to promote a stable set-up, these appliances are provided with adjustable feet (see Annex 2,
fig. 3). These feet can be adjusted by means of the supplied socket screwdriver.
Ø
Remove the vermiculite from the bottom (see paragraph 9.7.1.3.1 Instyle / Prostyle 700 / 800 / 1000 or 9.7.2.4.1
Instyle / Prostyle Tunnel.)
Ø
Turn the socket screwdriver to the right in order to adjust the fire upwards, and to the left to adjust the fire
downwards.
9.7 Supplementary installation instructions per appliance
9.7.1 Instyle / Prostyle 700 / 800 / 1000
9.7.1.1 Outside air connection
It is possible to provide the fire with an outside air connection. This outside air connection is optionally available
as an (external air) kit. This kit can be used for a connection either on the bottom or rear of the appliance and is
available through your supplier. First determine if you want a connection on the bottom or rear side.
Proceed as follows with a connection on the bottom (see Appendix 2, Fig. 17a + 17b):
Ø
Fasten the ‘pipe opening’ with 4 screws to the small housing.
Ø
Remove the 4 screws on the bottom side of the appliance.
Ø
Then bring the small housing with assembled ‘pipe opening’ against the plate on the bottom of the appliance.
Ø
Re-use the 4 screws to assemble the small housing.
Ø
Connect the flexible hose (Ø 80 mm) to the round ‘pipe opening’ of the outside air connection.
Ø
Dispose of unused parts in the appropriate way.
Proceed as follows with a connection on the rear (see Appendix 2, Fig. 17c + 17d):
Ø
Use a hammer to break the rectangular plate out of the rear of the appliance.
Ø
Also break out the side baffle in the middle of the external air kit.
Ø
Fasten the ‘pipe opening’ with 4 screws to the small housing.
Ø
Assemble the large housing on the small housing using 2 screws and set this to the correct length for the relative
appliance.
Ø
Remove the 6 screws on the bottom side of the appliance.
Ø
Then bring the outside air connection against the plate on the bottom of the appliance.
Ø
Re-use the 6 screws to assemble the external air kit.
Ø
Connect the flexible hose (Ø 80 mm) to the round ‘pipe opening’ of the outside air connection.
42
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Instyle 800V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Instyle 800V in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Instyle 800V

Dik Geurts Instyle 800V User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info