695347
39
Zoom out
Zoom in
Previous page
1/112
Next page
English
INSTALLATION MANUAL
9. Appliance-specific information
!CAUTION
The appliance-specific instructions as described in this section prevail over the instructions in the other
sections! If in doubt follow the instructions in section 9 or contact your supplier.
The appliance-specific information as described in paragraphs 9.1 to 9.5 applies to all models described in
this manual. Supplementary installation instructions (per appliance) are described in paragraph 9.6.
9.1 Smoke control area United Kingdom
The DG Fires Instyles/Prostyles 700 (except for the Instyles/Prostyles Tunnel appliances) have been recommended
as suitable for use in smoke control areas when burning wood. In smoke control areas in the United Kingdom the
air slide valve may not be closed too far because of emission laws. A limiting screw is accordingly supplied with all
appliances. This is supplied as a kit in the combustion chamber. This screw is therefore only used in the smoke
control areas in the United Kingdom. In other countries this screw can be disposed of in the appropriate way.
With the installation of an appliance in the United Kingdom:
Ø
Install the screw as shown in Appendix 2, Fig. 3a + 3b. After fitting, the air slide valve cannot be slid further shut
than legally allowed.
9.2 Convection connection and connection of the flue
9.2.1 Convection air connection
This appliance is provided with removable convection plates that have to be broken out when creating chimney
breast ventilation. The openings that are created in this way can be used to make a connection for convection air.
Here, hot convection air (outflow) is taken to a ventilation opening in the chimney breast. No extra provisions are
required for the inflow of cold convection air. The accessories needed for the outflow are available through your
supplier.
Various options are available for creating a convection air connection. Select the situation that applies to you and
proceed as follows:
New situation (hollow chimney breast made of non combustible material):
Option1:
Ø
Using a hammer, break out the plates for the convection air connection at the top of the appliance
(see appendix 2, fig. 4a).
Ø
Place the rings on the convection openings (see appendix 2, fig. 4b).
Ø
Slide a heat-resistant, flexible hose (Ø 125 mm) over the ring and fasten it with a hose clip or a self-tapping screw.
Ø
Connect the flexible hose to a ventilation element in the top of the chimney breast (at least 30 cm below the
ceiling). These accessories are available through your supplier.
Option 2:
Ø
Using a hammer, break out the 2 convection openings at the top of the appliance (see appendix 2, fig. 4a).
Ø
Place 2 ventilation elements in the top section of the chimney breast (at least 30 cm below the ceiling).
Option 3:
Ø
Do not break out the plates for the convection air connection.
Ø
Place 2 ventilation elements below the appliance to supply relatively cold air.
Ø
Place 2 ventilation elements above the fire (at least 30 cm below the ceiling).
!Caution
This option is not available in combination with a construction frame.
Existing situation or conversion without a hollow chimney breast
Ø
Do not break out the plates for the convection air connection.
Ø
The convection breast of the fire will provide sufficient convection flow.
39
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Instyle 800V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Instyle 800V in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Instyle 800V

Dik Geurts Instyle 800V User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info