695341

Dik Geurts Instyle 1000 Manual

44
Zoom out
Zoom in
Previous page
1/112
Next page
English
INSTALLATION MANUAL
9.7.2 Instyle Tunnel / Prostyle Tunnel
9.7.2.1 Air slide valve
Pior to installing the appliance, check the operation of the air slide (see appendix 2, fig. 20a and 20b). It is possible
that steel grit ended up in the air slide during transportation. If the air slide does not run smoothly, it has to be
cleaned. For this, the air slide should be disassembled. The suspended air slide valve is spring-mounted using a
bolt and a spring, which are located below the cover plate.
When disassembling the air slide, proceed as follows (see appendix 2, fig. 20a and 20 b):
!Caution
Has an outside air connection been mounted? If so, this should be removed first (see appendix 2, fig. 20b and
section 9.7.2.2).
Ø
Remove the vermiculite plates from the bottom (see chapter 9.7.3.2.1).
Ø
Unscrew the 5 Allen screws of the cover plate from the bottom and remove them.
Ø
Unscrew the Allen screw with spring.
Ø
Remove the air slide by bringing it towards you.
Ø
Check the air slide and clean it if necessary.
For placing back the air slide, the actions described for disassembling should be performed in reverse order.
9.7.2.2 Outside air connection
It is possible to provide the appliance with an outside air connection. This outside air connection is optionally
available (as an external kit). This kit can be used for a connection on the bottom of the appliance and is available
through your supplier.
!Caution
It is possible that the outside air connection is pre-mounted at delivery. This will be the case for an RS (room
sealed) version. Observe the steps as described under the heading 'Outside air connection pre-mounted'.
When assembling the outside air connection, proceed as follows:
Outside air connection not pre-mounted (see appendix 2, fig. 21):
Ø
Remove the lever at the bottom of the appliance by loosening the 2 screws and removing them.
Ø
Remove the 4 screws at the bottom of the appliance.
Ø
Place the tray with mounted pipe opening against the bottom of the appliance.
Ø
Re-use the 4 screws to mount the tray.
Ø
Place back the lever and fasten it by means of the 2 screws.
Ø
Connect the flexible hose (Ø 80 mm) to the round pipe opening of the outside air connection.
!Caution
In case of a fully closed system, always ensure an air-tight connection of the flexible hose to the round pipe
opening by using a heat resistant sealant.
For disassembling the outside air connection, please observe the above-mentioned steps in reverse order.
Outside air connection pre-mounted (see appendix 2, fig. 22):
Ø
Connect the flexible hose (Ø 80 mm) to the round pipe opening of the outside air connection.
!Caution
In case of a fully closed system, always ensure an air-tight connection of the flexible hose to the round pipe
opening by using a heat resistant sealant.
For disassembling the outside air connection, please observe the above-mentioned steps in reverse order.
44
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Instyle 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Instyle 1000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Instyle 1000

Dik Geurts Instyle 1000 User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info