499302
29
Zoom out
Zoom in
Previous page
1/54
Next page
29 DVB-S Receiver
GB
• When you press [Red] it will display “New TP” in “TP Index” item. You have to set the
parameters of “TP Frequency”, “Symbol Rate” for this new transponder. Therefore
use the number buttons of the RCU. The available range are “3000~13450MHz” and
“1000~45000KS/s”.
• When you press [Green] a safety question will be displayed for confi rmation to delete
the current transponder or not. If you select “OK”, the current transponder will be
deleted and the total number of transponders will be reduced.
• When you press [Yellow] a safety question will be displayed for confi rmation to delete
all transponders or not. If you select “OK”, the all transponders on current satellite will
be deleted.
3. For existing transponders you also can use number buttons to modify the param-
eters of “TP Frequency” and “Symbol Rate” or [Vol ] to change the value directly.
“Polarity” and “FTA only” are used for setting scans conditions. Press [Vol ] to
select a different mode.
On “TP Scan” item, press [OK] will open another window where you can set “Scan
Mode”, “Program Type” and “NIT Search”. Press [Menu/Exit] to return to the
previous menu.
Press [Red] button to add a new TP.
Press [Green] button to delete the current TP.
Press [Yellow] button to delete all transponders on current satellite
4. Antenna Setup: Press [OK] to enter LNB
confi guration, you will see a window like
beside:
LNB Type:
Press [Vol ] to switch among “Stand-
ard”, “User” and “Universal” mode.
For Example: If you use a Dual LNB, then
you should select “User” option in “LNB
Type” and set the correct frequency in
LNB type.
22K: Use [Vol ] to switch “ON” and “Off”. The 22KHz signal is used in KU universal
LNBs to change between low band and high band.
! Notice:
After choosing LNB type “Universal” you cannot modify 22K.
DiSEqC1.0:
Use [Vol ] to switch the options or press [OK] to open the DiSEqC1.0 option list to
select directly with[CH ] , press [OK] to confi rm it.
4. INSTALLATION
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Digitalbox IMPERIAL DB 2 USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Digitalbox IMPERIAL DB 2 USB in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Digitalbox IMPERIAL DB 2 USB

Digitalbox IMPERIAL DB 2 USB User Manual - German - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info