Manual Di Blasi R30 (page 23 of 28) (English, German, French, Italian, Spanish)

648032

23

Zoom out

Zoom in

Previous page

1/28

Next page

5. EINSTELLUNGEN UND KONTROLLEN

5.1 Reifen

Einzustellender Reifendruck:

•0,21 Kpa (2,1 atm) (30 psi)

Beim Aufpumpen eines Reifens sicherstellen, dass

er korrekt auf die Felge gezogen ist (die Bezugslinie

am Reifen muss an beiden Seiten überall den glei-

chen Abstand zur Felge haben).

Sicherstellen, dass das Ventil des Luschlauches

senkrecht zur Felge steht.

Im Sommer bei längerer Sonneneinwirkung oder

wenn der Scooter per Lufracht transportiert

werden soll, ca. ein Drittel der Lu aus den Reifen

ablassen.

5.3 Einstellung der Bremsen

Wenn die Bremskra der Handbremse nachlässt,

die Bremsbacken nachstellen. Hierzu die Schrau-

be des Drahtspanners am Ende des Bremshebels

und/oder die Schraube des Drahtspanners am

Bremsbackenhalter regulieren.

5.3.1 Einstellung am Hebel (Abb. 5.3.1)

•Die Mutter (A) lösen

•Zum Nachstellen der Bremse die Schraube

(B) lösen

•Die Mutter (A) wieder festziehen, dabei die

Schraube (B) xieren

•Das Rad bewegen, um sicherzustellen, dass

es hindernisfrei dreht, und die Bremskra

prüfen

•Falls erforderlich, die Einstellung erneut vor-

nehmen

•Nach vorgenommener Einstellung sicherstel-

len, dass der Knopf (F) der Feststellbremse

betätigt werden kann

5.3.2 Einstellung am Bremsbackenhalter

(Abb. 5.3.2)

•Die Mutter (A) lösen

•Zum Nachstellen der Bremse die Schraube

(B) lösen

•Die Mutter (A) wieder festziehen, dabei die

Schraube (B) xieren

•Das Rad bewegen, um sicherzustellen, dass

es hindernisfrei dreht, und die Bremskra

prüfen. Falls erforderlich, die Einstellung er-

neut vornehmen.

Bei optimaler Einstellung wird eine eziente

Bremskra auch dann erreicht, wenn der Bremshe-

bel bei vollem Zug nicht den Lenker berührt.

Wenn die Bremskra mit den Schrauben der

Drahtspanner nicht mehr wiederhergestellt wer-

den kann, die Bremsbacken in einer Werkstatt

auswechseln lassen.

D

5. CONTROLES ET REGLAGES

5.1 Pneus

La pression de gonage des pneus est:

•0,21 Kpa (2,1 atm) (30 psi)

Quand vous gonez un pneu, assurez vous qu’il

soit bien centré sur la jante (la ligne de référen-

ce toujours à la même distance du bord de la

jante, sur les deux cotés). Assurez vous aussi

que la valve de la chambre à air sorte droite à

travers le trou de la jante.

Dégonez les pneus d’un tiers en cas d’exposi-

tion prolongée à un fort soleil d’été ou en cas

d’expédition par avion.

5.3 Réglage des freins

Dés que le freinage manuel commence à perdre

son ecacité, il est nécessaire de rattraper l’usu-

re des patins du frein.

Ce réglage s’eectue par le vérin situé à l’ex-

trémité du levier du frein et/ou au plateau du

frein sur la roue

5.3.1 Réglage au levier (F. 5.3.1)

•Débloquer le contre écrou (A)

•Pour augmenter l’ecacité du frein, dévissez

le vérin (B);

•Bloquer le contre écrou (A) en s’assurant que

le vérin (B) ne tourne pas avec lui ;

•Faire tourner la roue pour s’assurer qu’elle est

libre et vériez l’ecacité du frein.

•Répéter à nouveau le réglage si nécessaire.

•Après le réglage, assurez vous que le bouton

(F) du frein de parking puisse s’insérer régu-

lièrement

5.3.2 Réglage au plateau du frein (F. 5.3.2)

•Débloquer le contre écrou (A)

•Pour augmenter l’ecacité du frein, dévissez

la vis (B);

•Bloquer le contre écrou (A) en s’assurant que

la vis (B) ne tourne pas avec lui ;

•Faire tourner la roue pour s’assurer qu’elle est

libre et vériez l’ecacité du freinage. Répéter

à nouveau le réglage si nécessaire.

Le réglage est bien fait si on obtient un freinage

ecace quand, tout en tirant la poigné du frein

au maximum, elle ne touche pas le guidon.

Quand il n’est plus possible rattraper l’usure des

patins du frein en agissant sur les vis de régla-

ge, faites remplacer les patins chez un atelier

de réparation.

F

5. CONTROL Y NORMATIVAS

5.1 Neumáticos

La presión de hinchado de los neumáticos debe

ser la siguiente:

•0,21 Kpa (2,1 atm) (30 psi)

Al hinchar un neumático, compruebe que se en-

cuentre centrado en la estructura radial (la línea

de referencia del neumático debe encontrarse

siempre equidistante del borde de la estructura

radial por ambos lados).

Compruebe que la válvula de la cámara de aire se

encuentre en perpendicular a la estructura radial.

En caso de exposición prolongada al sol en vera-

no o de que el escúter sea transportado en avión,

deshinche los neumáticos en una tercera parte.

5.3 Regulación de los frenos

Cuando el freno manual empiece a perder e-

ciencia, hay que reparar el desgaste del material

de fricción realizando las siguientes operacio-

nes sobre el tornillo tensor situado en el extre-

mo de la palanca de freno o en el tornillo tensor

de la placa:

5.3.1 Regulación de la palanca (F. 5.3.1)

•Desbloquee la contratuerca (A)

•Para aumentar la ecacia del freno, aoje el

tornillo (B)

•Apriete de nuevo el perno (A) manteniendo

apretado el tornillo (B)

•Haga girar la rueda para asegurarse de que lo

hace libremente y compruebe la ecacia del

freno.

•En caso de que resulte necesario, vuelva a re-

gular la palanca.

•Tras regular la palanca, compruebe que pue-

de apretar el botón (F) del freno e estaciona-

miento.

5.3.2 Regulación del bloqueo (F. 5.3.2)

•Desbloquee la contratuerca (A)

•Para aumentar la ecacia del freno, aoje el

tornillo (B)

•Apriete de nuevo la tuerca (A) manteniendo

apretado el tornillo (B)

•Haga girar la rueda para asegurarse de que lo

hace libremente y compruebe la ecacia del

freno. En caso de que resulte necesario, vuel-

va a regular la placa.

La regulación es ideal si se consigue un frenado

ecaz cuando, aunque se tire al máximo de la

palanca de freno, esta no llega a tocar el manillar.

Si no se puede recuperar la eciencia de los fre-

nos mediante estas operaciones sobre los tornil-

los tensores, sustituya el material de desgaste en

un taller de reparación.

E

5. CHECKS AND ADJUSTMENTS

5.1 Tyres

Tyres inating pressure is:

•0,21 Kpa (2,1 atm) (30 psi)

While inating be sure that the rim line of the

tyre is at an even distance from the rim all the

way around on both sides.

Make sure that the valve stem is straight up

through the hole in the wheel rim.

Deate tires of about 1/3 when the scooter is

le for long time under the summer sun or is

dispatched by airplane.

5.3 Brakes adjustment

As soon as the manual brake begin to lose ef-

ciency, it is necessary to recover the wear of

the brake shoes.

Adjustment can be eected by means of the

adjusters at the brake lever and/or at the brake

shoes holder:

5.3.1 Adjustment at the lever (F. 5.3.1)

• Unlock the lock nut (A);

•To tighten the brake, unscrew the hollow

screw (B)

•Lock the lock nut (A) making sure that the

hollow screw (B) does not turn with it.

•Spin the wheel to check that it turns freely

and test brake eciency.

•Readjust if necessary.

•Aer adjustment, check that the parking but-

ton (F) can be pressed normally

5.3.2 Adjustment at the brake shoes holder

(F. 5.3.2)

•Unlock the lock nut (A);

•To increase brake eciency, unscrew the

screw (B)

•Lock the lock nut (A) making sure that the

screw (B) does not turn with it.

•Spin the wheel to check that it turns freely

and test brake eciency. Readjust if neces-

sary

Adjustment is well made when the maximum

braking eciency is obtained before that the

brake lever touches the handlebar.

When it is no more possible to recover the bra-

ke eciency only through the adjusters, ask to a

repair shop to replace the brake shoes.

GB

1

How do you set up the points on a do blasi scooter? Submitted on 2-6-2023 at 14:55
Reply Report abuse
My scooter won't unfold. Can I unfold it manually? Submitted on 17-1-2023 at 16:17
Reply Report abuse
- There is a switch on the handlebar which disables all the electric.
  Flip it and the device will then be able to be manually erected. Answered on 17-1-2023 at 20:53
  Vote up Report abuse
The r30 mobility scooter won't unfold. Checked battery. Ok. Can I unfold it manually? Submitted on 17-1-2023 at 16:09
Reply Report abuse
- this happened to me first take off the battery then put it back in again make sure it is well in now try again it might work OK if it dosent yes you can fold it manually good luck Answered on 17-1-2023 at 16:15
  Vote up Report abuse
i cannot get my di blasi 30 to engage with battery so not in use folds unfolds but wont engage to go has anyone else had this problem Submitted on 22-9-2022 at 15:14
Reply Report abuse
What is the red button on Di Blasi R30 folding scooter Submitted on 8-7-2022 at 19:31
Reply Report abuse
- press red button to automatically fold down scooter chair Answered on 8-7-2022 at 19:45
  Vote up Report abuse
fully charged battery but motor dosent work i might have disturbed something lifting it in and out of car any info greatly received Submitted on 3-7-2022 at 18:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Di Blasi R30 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Di Blasi R30 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info