549677
34
Zoom out
Zoom in
Previous page
1/156
Next page
ENGLISH
32
NOTE: If using an adapter ensure it is firmly
attached to the tool outlet before following the
steps below.
a. Ensure the collar on the AirLock connector
is in the unlock position. Align notches (v) on
collar and AirLock connector as shown for
unlock and lock positions.
b. Push the AirLock connector onto the adapter
connector point.
c. Rotate the collar to the locked position.
NOTE: The ball bearings inside collar lock
into slot and secure the connection.The
power tool is now securely connected to the
dust extractor.
AUTOMATIC FILTER CLEANING SYSTEM
This vacuum has a highly effective filter cleaning
system which minimizes filter clogging. Every
30seconds, one of the two filters gets automatically
cleaned. The cleaning process alternates between
the filters and continues through the life of the unit.
NOTE: It is normal to hear a clicking sound during
this process.
NOTE: After many hours of operation the automatic
filter cleaning system may not be effective. When
this happens the filters will need to be cleaned or
replaced. Refer to Filter under Maintenance.
PARKING BRAKE (FIG. 1, 6)
The parking brake will lock one wheel in place to
prevent vacuum from rolling.
1. To engage parking brake, depress
the brake button (x) to snap the brake into the
locked position.
2. To disengage parking brake, depress the brake
button and brake will snap into the unlocked
position.
REMOVE / CHANGE USED DUST COLLECTION BAG (FIG. 1)
WARNING: Appropriate personal
protective equipment like dust mask and
gloves should be used while handling
used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Close the twist-lock hose inlet (j) with the inlet
plug (s).
3. Unlatch canister latches (d) and remove vacuum
head (c)
4. Pull the collection bag carefully from inlet (j).
5. Seal the collection bag opening tightly when
removing it from the machine.
6. Dispose of collection bag in appropriate
container according to statutory provisions.
WET PICK UP APPLICATIONS (FIG. 1, 7)
WARNING: DO NOT connect power
tools to outlet (m) when using the
vacuum for wet pick up.
WARNING: Plug vacuum into residual
current device (RCD) protected outlet
when using the vacuum for wet pick up.
WARNING: If foam or liquid escapes
from the machine, switch off
immediately.
CAUTION: Clean the water level limiting
device regularly and examine it for signs
of damage.
NOTICE: DO NOT remove ball float
(y), doing so will cause damage to the
vacuum. The ball float keeps water from
entering the motor.
Before using the vacuum for wet pick up:
Ensure the canister is empty and free of
excessive dust.
Remove filters (i).
Plug vacuum into a RCD protected outlet.
WARNING: Do not use the machine
with this set up for dust Class L and M.
TO EMPTY CANISTER (FIG. 1, 7)
The ball float valve (y) will block air to the motor
when the canister is full and the sound of the motor
will change at once. When the motor has a high
pitched sound and air/water flow stops, empty the
canister.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch canister latches (d) and remove vacuum
head (c).
3. Empty contents of canister (f) into a suitable
container or drain.
TO CONVERT BACK TO DRY VACUUM OPERATION (FIG. 1)
1. Empty Canister, refer to To Empty Canister
instructions.
2. Place canister upside down position until dry.
DO NOT use wet canister for dry pick up.
3. Place vacuum head (c) on a level surface until
dry.
4. Reinstall filters when vacuum head is dry. See
Filters under Maintenance.
5. When canister is dry place the vacuum head (c)
onto the canister and secure it by closing the
canister latches (d).
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWV902L T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWV902L T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DWV902L T 1

DeWalt DWV902L T 1 Additional guide - Polish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info