Manual DeWalt DWE4051 T 2 (page 44 of 208) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

548029

Zoom out

Zoom in

1/208

ENGLISH

b. The ring on the threaded clamp nut (e) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button (a) and rotate the

spindle (b) until it locks in position.

6. Tighten the threaded clamp nut (e) with the hex

key provided or a two pin spanner.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (e) with the hex key provided or a two pin

spanner.

NOTE: Edge grinding can be performed with Type

27 wheels designed and specified for this purpose;

6 mm thick wheels are designed for surface grinding

while 3 mm wheels are designed for edge grinding.

Cutting can be performed by using a Type 1 wheel

and a Type 1 guard.

Mounting Wire Brushes

andWire Wheels

Wire cup brushes or wire wheels screw directly

on the grinder spindle without the use of flanges.

Use only wire brushes or wheels provided with a

M14threaded hub. A Type 27 guard is required

when using wire brushes and wheels.

CAUTION: Wear work gloves when

handling wire brushes and wheels.

They can become sharp.

CAUTION: Wheel or brush must not

touch guard when mounted or while

in use. Undetectable damage could

occur to the accessory, causing wires to

fragment from accessory wheel or cup.

1. Thread the wheel on the spindle by hand.

2. Depress spindle lock button and use a wrench

on the hub of the wire wheel or brush to tighten

the wheel.

3. To remove the wheel, reverse the above

procedure.

NOTICE: Failure to properly seat the

wheel hub before turning the tool on

may result in damage to tool or wheel.

Fitting and Removing a

Backing Pad/Sanding Sheet

1. Place the tool on a table or flat surface, with the

guard facing up.

2. Remove the backing flange (d).

3. Place the rubber backing pad correctly onto the

spindle (b).

4. Place the sanding sheet on the rubber backing

pad.

5. Screw the threaded clamp nut (e) onto the

spindle. The ring on the threaded clamp nut

must face towards the rubber backing pad.

6. Press the spindle lock button (a) and rotate the

spindle (b) until it locks in position.

7. Tighten the threaded clamp nut (e) with the hex

key provided or a two pin spanner.

8. Release the spindle lock.

9. To remove the rubber backing pad, loosen

the threaded clamp nut (e) with the hex key

provided or a two pin spanner.

Fitting a Wire Cup Brush

Screw the wire cup brush directly onto the spindle

without the use of the spacer and threaded flange.

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flanges are

mounted correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

WARNING:

• Ensure all materials to be ground or

cut are secured in place.

• Secure and support the workpiece.

Use clamps or a vice to hold and

support the workpiece to a stable

platform. It is important to clamp and

support the workpiece securely to

prevent movement of the workpiece

and loss of control. Movement of

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE4051 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 28,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DWE4051 T 2

DeWalt DWE4051 T 2 Additional guide - Polish - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWE4051 T 2 Manual

Product: