548029

DeWalt DWE4051 T 2 Manual

42
Zoom out
Zoom in
Previous page
1/208
Next page
ENGLISH
40
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see Technical Data).The minimum
conductor size is 1.5 mm
2
; the maximum length
is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle (fi g. 1)
WARNING: Before using the tool,
check that the handle is tightened
securely.
Screw the side handle (c) tightly into one of the holes
on either side of the gear case. The side handle
should always be used to maintain control of the
tool at all times.
Accessories and Attachments
It is important to choose the correct guards, backing
pads and flanges to use with grinder accessories.
Refer to chart at the end of this section for
information on choosing the correct accessories.
NOTE: Edge grinding can be performed with Type
27 wheels designed and specified for this purpose.
WARNING: Accessories must be rated
for at least the speed recom mended
on the tool warning label. Wheels and
other accessories running over rated
accessory speed may burst and cause
injury. Threaded accessories must
have a M14 hub. Every unthreaded
accessory must have a 22 mm arbor
hole. If it does not, it may have been
designed for a circular saw and should
not be used. Use only the accessories
shown in the chart at the end of this
section. Accessory ratings must be
above listed minimum wheel speed as
shown on tool nameplate.
Mounting Guards
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
CAUTION: Guards must be used with
this grinder.
When using the DWE4050 or the DWE4051 grinder
for cutting metal or masonry, a Type 1 guard MUST
be used. Type 1 guards are available at extra cost
from DEWALT distributors.
NOTE: Please refer to the Grinding and Cutting
Accessory Chart at the end of this section to
see other accessories that can be used with these
grinders.
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWE4051 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE4051 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 28,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DWE4051 T 2

DeWalt DWE4051 T 2 Additional guide - Polish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info