546640

DeWalt DWE396 Manual

29
Zoom out
Zoom in
Previous page
1/132
Next page
ENGLISH
27
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (fi g. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. On/off trigger switch
b. Lock-off button
c. Rear grip handle
d. Front handle
e. Saw blades
f. Bar
g. Hex key
h. Dust port
INTENDED USE
Your DEWALT alligator saw DWE396, DWE397,
DWE398 and DWE399 has been designed for
professional sawing applications of clay building
blocks, cellular concrete, wood, plastic and
insulation materials with suitable saw blade.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–
core extension cable suitable for the power input of
this tool (see technical data).The minimum conductor
size is 1.5 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Replacing the Saw Blades
REMOVING THE SAW BLADES (FIG. 2–5)
1. Place the tool upside down on a flat, stable
work surface.
2. Loosen the gearcase cap screw (k) with
the hex key (g). When loosened, the gearcase
cap (l) should release and spring open.
3. With the hex key (g), loosen both of the blade
setting screws (m). The screws will be held in
place by the screw clips.
4. Carefully pull the saw-blade-end up until it is
disengaged from and clear of the Blade-Clamp-
system.
5. Pull the saw blade back and out of the front
guard (n) and take it off of the bar (f).
6. Repeat this procedure for the other saw blade.
FITTING THE SAW BLADES (FIG. 4)
1. Slide one saw-blade into the blade guide slot (i)
making sure that the end with the slotted hole
(p) fits into the front guard (n).
2. Slide the back of the saw blade down until the
threaded hole (o) aligns with the blade setting
screw (m).
3. Repeat this procedure for the other saw blade.
4. Tighten both saw blade setting screws (m)
securely by pressing and turning simultaneously
with the short end of the hex key (g).
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWE396 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE396 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info