500493

DeWalt DWD221 Manual

27
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH
25
WARNING: To reduce the risk of
personal injury, ALWAYS operate
the tool with the side handle properly
installed. Failure to do so may result
in the side handle slipping during tool
operation and subsequent loss of
control. Hold tool with both hands to
maximise control.
WARNING: Do not attempt to tighten
or loosen drill bits (or any other
accessory) by gripping the front part
of the chuck and turning the tool on.
Damage to the chuck and personal
injury may occur.
Proper Hand Position (fi g. 1, 3)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the
side handle (c), with the other hand on the main
handle (f).
Trigger Switch (fi g. 2)
To run the tool, press the variable speed switch (a).
The pressure exerted on the variable speed switch
determines the tool speed.
If necessary, press the lock-on button (g) for
continuous operation and release the switch. The
lock-on button works only in full speed, forward
rotation.
To stop the tool, release the variable speed switch.
To stop the tool in continuous operation, press the
switch briefly and release it. Always turn the tool off
when work is finished and before unplugging.
Keyless Chuck (fi g. 4–6)
The DWD221 features a keyless chuck (d) for
greater convenience. To insert a drill bit or other
accessory, follow the steps listed below.
1. Grasp the rear half of the chuck with one hand
and use your other hand to rotate the front half
counterclockwise, as shown in Figure 4. Rotate
far enough so that the chuck opens sufficiently
to accept the desired accessory.
2. Insert the bit or other accessory about 3/4"
(19 mm) into the chuck and tighten securely
by holding the rear half of the chuck and
rotating the front portion in the clockwise
direction. When the chuck is nearly tightened,
you will hear a clicking sound. After 4–6 clicks,
the chuck is securely tightened around the
accessory.
3. To release the accessory, repeat step 1 listed
above.
WARNING: Do not attempt to tighten
or loosen drill bits (or any other
accessory) by gripping the front part
of the chuck and turning the tool on.
Damage to the chuck and personal
injury may occur.
KEYLESS CHUCK REMOVAL (FIG. 5)
Tighten the chuck around the shorter end of a hex
key (not supplied) of 1/4" (6 mm) or greater size.
Using a soft hammer or piece of wood, strike the
longer end in the counterclockwise direction. This
will loosen the chuck so that it can be unscrewed
by hand.
KEYLESS CHUCK INSTALLATION (FIG. 6)
Screw the chuck on by hand as far as it will go.
Tighten the chuck around the shorter end of a 1/4"
(6 mm) or larger hex key (not supplied). Strike the
longer end in the clockwise direction with a soft
hammer.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can
cause injury.
Lubrication
Your power tool requires no additional lubrication.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWD221 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWD221 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info