500493
26
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH
24
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Side Handle (fi g. 1)
WARNING: To reduce the risk of
personal injury, ALWAYS operate
the tool with the side handle properly
installed and tightened. Failure to do so
may result in the side handle slipping
during tool operation and subsequent
loss of control. Hold tool with both
hands to maximise control.
A side handle (c) is supplied with your drill. The side
handle clamps to the front of the gear case and can
be rotated 360 degrees to permit right- or left-hand
use.
After the side handle is rotated into position, it
should be pushed rearward until the slots (h) on the
lip of the side handle are aligned and fully engaged
with the projecting tabs (i) on the underside of the
gear case. The side handle is then securely clamped
by turning clockwise until tight.
Variable Speed Trigger Switch (fi g. 2)
The variable speed trigger switch (a) permits speed
control. The farther the trigger switch is depressed,
the higher the speed of the drill.
NOTE: Use lower speeds for starting holes, drilling
in plastics or ceramics or driving screws.
Reversing Lever (fi g. 2)
The reversing lever (b), located above the trigger
switch, changes the direction of rotation of the drill
and is used when backing out screws and jammed
drill bits.
To operate the tool in reverse, release the trigger
switch and push the lever to the left (when viewed
from the chuck end).
To operate the drill in forward, release the trigger
switch and push the lever to the right (when viewed
from the chuck end).
Return the reversing lever to the forward position
after all operations in reverse are completed.
Torque Limiting Clutch
This tool is equipped with a torque limiting clutch
that reduces the maximum torque reaction
transmitted to the operator in case of jamming of a
drill bit. This feature also prevents the gearing and
electric motor from stalling. The torque limiting clutch
has been factory-set and cannot be adjusted.
Motor Lock Control (fi g. 1)
Your DEWALT drill comes with an electronic
feature called motor lock control. It is designed to
help prevent the motor from being overloaded in
demanding applications during a stall situation. This
may be encountered when drilling in steel or using
large bits in wood.
As a stall situation presents itself, the motor cycles
on and off for a set period of time. This reduces the
reaction of the stall. Releasing the trigger resets the
motor lock control and the unit will operate in normal
mode when the trigger is depressed again.
Figure 1 shows the instruction label (j) mounted on
the housing. There are two alert modes:
1. Engaged Mode: When a stall situation
presents itself, the light will come on and stay
on as the motor cycles on and off for a set
period of time before the motor lock control
completely shuts the tool down. When the unit
is running in normal mode, there will be no light
2. Problem Mode: A series of continual flashes as
the trigger is pulled indicates that the electronics
are no longer functioning. The tool may still be
able to function without the benefit of motor
lock control but should be serviced as soon as
possible.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
“back-up” block to prevent damage to
the material.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWD221 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWD221 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info