Manual DeWalt DW754 T 2 (page 31 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546919

Zoom out

Zoom in

1/116

ENGLISH

1. Remove the fasteners holding the workpiece

support (c) to the bracket (d) and remove the

workpiece support (fig. 1).

2. Mount the grinding attachment bracket (v) to

the bracket (d) on the machine as shown using

the hexagonal head bolt (w) and corresponding

nut (x) (fig. 8). Make sure that the grinding

attachment bracket is at a distance of approx. 2

mm from the grinding wheel.

3. Insert the rod (y) of the grinding attachment into

the forks on the grinding attachment bracket as

shown.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Refer to figure 10 for proper body stance and hand

positioning when grinding and honing.

Switching On and Off (ﬁ g. 1)

To turn the tool on, set the on/off switch (a) to

position 1.

To turn the tool off, set the on/off switch (a) to

position 0.

Using the Grinding Wheel (ﬁ g. 1)

In order to achieve a straight cutting edge, move it

slowly backwards and forwards over the grinding

wheel (b). Only exert a light pressure.

Using the Clamping and Grinding

Attachment (ﬁ g. 9)

1. Insert the workpiece into the clamping bracket

(z).

2. Position the workpiece as required to obtain the

correct bevel angle. The angle is a function of

the protruding length X (see figure). For plane

irons, X should be approx. 20 mm, for chisels

approx. 25–28 mm.

3. Tighten the star knobs (aa).

Using the Honing Wheel (ﬁ g. 1)

Move the workpiece slowly horizontally backwards

and forwards over the honing wheel (e). The tip

of the cutting edge of the workpiece should be in

contact with the wheel over a width of 0.5 to 1 mm.

WARNING: Do not use any honing

paste on the honing wheel.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the switch is in the OFF position. An

accidental start-up can cause injury.

On a weekly basis, remove grindings from the

housing and the covers.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW754 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW754 T 2

DeWalt DW754 T 2 User Manual - Polish - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW754 T 2 Manual

Product: