Manual DeWalt DW754 T 2 (page 30 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546919

Zoom out

Zoom in

1/116

ENGLISH

ASSEMBLY AND ADJUSTMENT

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the switch is in the OFF position. An

accidental start-up can cause injury.

Unpacking the Machine and its Parts

1. Carefully lift the machine out of its package.

2. Take out the accessories and hardware parts.

Required and Recommended Tools

Apart from the tools included with the machine, the

following tools are required:

–Torque wrench

Mounting the Machine to the

Workbench (ﬁ g. 2)

The machine must be mounted onto the

workbench.

1. Mark the position of the four mounting holes

provided in the base of the machine on the

workbench.

2. Drill a Ø 6.5 mm hole at each of the marked

positions.

3. Place the machine on the workbench and insert

an M6 bolt with a washer through the mounting

holes in the base into each of the holes drilled in

the workbench. Make sure the protruding length

X (see figure) is at least 15 mm for each of the

bolts used.

4. Place a nut on each of the bolts and securely

tighten the nuts (torque: 8 Nm).

Changing the Grinding Wheel

(ﬁ g. 3, 4)

1. Remove the three nuts (g) using the spanner

supplied.

2. Remove the guard cover (h).

3. Remove the nut (i) from the spindle (j) using the

spanner supplied. The nut on the right spindle

has a right thread (fig. 3), the nut on the left

spindle a left thread (fig. 4).

4. Take the outer flange (k), the packing piece (l)

and the wheel (m) from the spindle.

5. Place the new wheel onto the spindle.

6. Replace the packing piece, the outer flange and

the nut on the spindle.

7. Securely tighten the nut (i) (torque: 6 Nm).

8. Replace the guard cover.

9. Replace the three nuts (g) and securely tighten

them (torque: 5 Nm).

10. Switch on the machine and let the wheel run

with no load for one minute to check for cracks.

WARNING: Do not use a damaged

wheel.

Mounting the spark guard

(ﬁ g. 5, 6)

The spark guard offers additional protection from

sparks and should be used whenever possible. A

spark guard is supplied for each wheel.

1. Fit the transparent screen (n) to the spark guard

(f) by inserting a mushroom head bolt (o) into

the screen and the guard and placing a washer

(p) and nut (q) onto the bolt (fig. 5). Tighten the

nut.

2. Hold the spark guard against the edge on top

of the wheel case (r) as shown (fig. 6).

3. Insert a mushroom head bolt (s) into the guard

and the wheel case.

4. Place a washer (t) and nut (u) onto the bolt and

tighten the nut hand-tight.

5. Position the guard at a distance of approx. 2

mm from the wheel by sliding it towards the

wheel.

6. Securely tighten the nut (torque: 6 Nm).

Adjusting the workpiece support

(ﬁ g. 7)

The workpiece support can be set according to the

workpiece and the desired grinding angle.

1. Slacken the nut holding the support (c).

2. Set the support to the desired position and

angle, making sure that the support is as close

to the wheel as possible.

3. Tighten the nut (torque: 6 Nm).

Mounting and adjusting the

clamping and grinding attachment

(ﬁ g. 1, 8)

The clamping and grinding attachment is used to

hold the workpiece to the grinding wheel at a fixed

angle.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW754 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW754 T 2

DeWalt DW754 T 2 User Manual - Polish - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW754 T 2 Manual

Product: