546917

DeWalt DW753 Manual

31
Zoom out
Zoom in
Previous page
1/124
Next page
ENGLISH
29
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data). The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENT
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the switch is in the OFF position. An
accidental start-up can cause injury.
Unpacking the Machine and its Parts
1. Carefully lift the machine out of its package.
2. Take out the accessories and hardware parts.
Required and Recommended Tools
Apart from the tools included with the machine, the
following tools are required:
–Torque wrench
Mounting the Machine to the
Workbench (fi g. 2)
The machine must be mounted onto the
workbench.
1. Mark the position of the four mounting holes
provided in the base of the machine on the
workbench.
2. Drill a Ø 6.5 mm hole at each of the marked
positions.
3. Place the machine on the workbench and insert
an M6 bolt with a washer through the mounting
holes in the base into each of the holes drilled in
the workbench. Make sure the protruding length
X (see figure) is at least 15 mm for each of the
bolts used.
4. Place a nut on each of the bolts and securely
tighten the nuts (torque: 8 Nm).
Changing the Grinding Wheel (fi g. 3)
1. Remove the three nuts (j) using the spanner
supplied.
2. Remove the guard cover (k).
3. Remove the nut (l) from the spindle (m) using
the spanner supplied.
4. Take the outer flange (n), the packing piece (o)
and the wheel (p) from the spindle.
5. Place the new wheel onto the spindle.
6. Replace the packing piece, the outer flange and
the nut on the spindle.
7. Securely tighten the nut (l) (torque: 6 Nm).
8. Replace the guard cover.
9. Replace the three nuts (j) and securely tighten
them (torque: 5 Nm).
10. Switch on the machine and let the wheel run
with no load for one minute to check for cracks.
WARNING: Do not use a damaged
wheel.
Changing the Grinding or Honing Belt
(fi g. 4)
1. Remove the knob (i).
2. Loosen the nut (q) a few turns.
3. Lift and remove the cover (r).
4. Remove the backing plate (s).
5. Turn the tensioning lever (g) counter-clockwise
to release tension and keep the lever in this
position.
6. Remove the belt (t).
7. Place a new belt over the pulleys (u), making
sure that the arrow on the inside of the belt
points in the same direction as the arrow (v) on
the backing plate.
8. Release the lever.
9. Holding the threaded pin (w) in its place, replace
the backing plate.
10. Replace the cover and tighten the nut.
11. Replace the knob and tighten it.
WARNING: When mounting a leather
honing belt, make sure that the leather
surface is on the outside.
Adjusting the Grinding or Honing Belt
(fi g. 5)
CENTERING THE BELT
If the belt (e) is not properly centered, adjust by
turning the centering knob (h).
ADJUSTING THE BELT TO THE WORKPIECE
The belt can be adjusted to suit workpieces with
concave, convex or straight cutting edges.
1. Slacken the knob (i).
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW753 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW753 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW753

DeWalt DW753 User Manual - Polish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info