Manual DeWalt DW745 T 4 (page 37 of 188) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546618

Zoom out

Zoom in

1/188

ENGLISH

• Consider applying specially designed noise-

reduction blades.

• Do not use high steel (HS) saw blades.

• Do not use deformed, cracked or damaged saw

blades.

• Ensure that the chosen saw blade is suitable for

the material to be cut.

• Always wear gloves for handling saw blades

and rough material. Saw blades should be

carried in a holder wherever practicable.

Residual risks

The following risks are inherent to the use of saws:

- injuries caused by touching the rotating parts

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered

parts of the rotating saw blade.

- Risk of injury when changing the saw blade with

unprotected hands.

- Risk of squeezing fingers when opening the

guards.

- Health hazards caused by breathing dust

developed when sawing wood, especially oak,

beech and MDF.

The following factors are of influence to noise

production:

- the material to be cut

- the type of saw blade

- the feed force

- machine maintenance

The following factors are of influence to dust

exposure:

- worn saw blade

- dust extractor with air velocity less than 20 m/s

- workpiece not exactly guided

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use

Wear ear protection

• During transportation make sure that the upper

part of the saw blade is covered, e.g. by the

guard.

• Do not use the guard for handling or

transportation.

WARNING: This machine is equipped

with a specially configured power supply

cord(type Y attachment). If the power

supply cord is damaged or otherwise

defective, it must only be replaced by

the manufacturer or by an authorised

repair agent.

• Immediately replace the table insert (throat

plate) when worn or damaged.

• Check that the workpiece is properly supported.

Always provide additional support for long

workpieces.

• Do not exert side pressure on the saw blade.

• Never cut light alloy. The machine is not

designed for this application.

• Do not use abrasive disc or diamond cutting

wheels

• Rabbeting, slotting or grooving is not allowed.

• In case of an accident or machine failure,

immediately switch the machine off and pull the

plug. Report the failure and mark the machine in

suitable form which prevents that other persons

use the defective machine.

• When the saw blade is blocked due to

abnormal feed force during cutting, ALWAYS

switch the machine off and disconnect from

power supply. Remove the workpiece and

ensure that the saw blade runs free. Turn the

machine on and start a new cutting operation

with reduced feed force.

• Always connect the circular saw to a dust

collection device when sawing wood.

• NEVER attempt to cut a stack of loose pieces

of material which could cause loss of control or

kickback. Support all materials securely.

SAW BLADES

• When sawing wood always connect the

machine with suitable dust extractor.

• The max. allowable speed of the saw blade

must always be equal to or greater than the

no-load speed of the tool specified on the

nameplate.

• Do not use saw blades that do not conform to

the dimensions stated in the Technical Data.

Do not use any spacers to make a blade fit onto

the spindle. Use only the blades specified in this

manual, complying with EN 847-1, if intended

for wood and similar materials.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW745 T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW745 T 4 Manual

Product: