Manual DeWalt DW739 T 2 (page 19 of 76) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546446

Zoom out

Zoom in

1/76

ENGLISH

12 en - 2

6 Store idle tools

When not in use, Power Tools must be stored in a dry place and

locked up securely, out of reach of children.

7 Dress properly

Do not wear loose clothing or jewellery. They can be caught in moving

parts. Preferably wear rubber gloves and non-slip footwear when

working outdoors. Wear protective hair covering to keep long hair out

of the way.

8 Wear safety goggles

Also use a face or dust mask in case the operations produce dust or

flying particles.

9 Beware of maximum sound pressure

Take appropriate measures for the protection of hearing if the sound

pressure of 85 dB(A) is exceeded.

10 Secure workpiece

Use clamps or a vice to hold the workpiece. It is safer and it frees both

hands to operate the tool.

11 Do not overreach

Keep proper footing and balance at all times.

12 Avoid unintentional starting

Do not carry the plugged-in tool with a finger on the switch.

Be sure that the switch is released when plugging in.

13 Stay alert

Watch what you are doing. Use common sense. Do not operate the

tool when you are tired.

14 Disconnect tool

Shut off power and wait for the tool to come to a complete standstill

before leaving it unattended. Unplug the tool when not in use, before

servicing or changing accessories.

15 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed from the

tool before operating the tool.

16 Use appropriate tool

The intended use is described in this instruction manual. Do not force

small tools or attachments to do the job of a heavy-duty tool. The tool

will do the job better and safer at the rate for which it was intended.

Warning! The use of any accessory or attachment or performance of

any operation with this tool, other than those recommended in this

instruction manual may present a risk of personal injury.

17 Do not abuse cord

Never carry the tool by its cord or pull it to disconnect from the socket.

Keep the cord away from heat, oil and sharp edges.

18 Maintain tools with care

Keep the tools in good condition and clean for better and safer

performance. Follow the instructions for maintenance and changing

accessories. Inspect the tool cords at regular intervals and,

if damaged, have them repaired by an authorized DEWALT repair

agent. Inspect the extension cords periodically and replace them if

damaged. Keep all controls dry, clean and free from oil and grease.

19 Check for damaged parts

Before using the tool, carefully check it for damage to ensure that it will

operate properly and perform its intended function. Check for

misalignment and seizure of moving parts, breakage of parts and any

other conditions that may affect its operation. Have damaged guards

orother defective parts repaired or replaced as instructed.

Do not use the tool if the switch is defective. Have the switch replaced

by an authorized DEWALT repair agent.

20 Have your tool repaired by an authorized DEWALT repair agent

This Power Tool is in accordance with the relevant safety regulations.

To avoid danger, electric appliances must only be repaired by qualified

technicians.

Additional safety instructions for bandsaws

• It is advisable to wear safety goggles when operating.

• Keep the upper blade guard as close to the workpiece as possible.

• When not in use, protect the saw blade completely using the blade guard.

• When not in use, when changing blades or carrying out maintenance,

disconnect the machine from the power supply.

• Before switching ON, make sure that the worktable is secured at the

required angle.

• Always use sharp blades of the correct type designed for the

workpiece.

• Keep your hands well clear off the blade. Use a push stick for narrow

workpieces.

• Always make sure that the table insert is properly located. Replace the

insert immediately when worn.

• Never run the machine without all guards in place and the door locked.

• When working under abnormal conditions (exceptionally low

temperatures, lower mains supply voltage than normal or following a

long period of inactivity) the machine may have a tendency to stick.

In such a case, slacken the blade tension to approx. 100 N, switch the

motor ON and (while the motor is running) gradually increase the

tension to (50 x b) N, where b is the width of the saw blade in mm.

• When the machine is not going to be used for a prolonged period of

time, slacken the tensioner completely to eliminate the risk of blade

wheel distortion and resulting imbalance.

• Always secure round workpieces.

• Make sure that the blade rotates in the correct direction and that the

teeth are pointing downwards.

Residual risks

The following risks are inherent to the use of these saws:

- injuries caused by touching the rotating parts

- injuries caused by disruption of the saw blade

These risks are most evident:

- within the range of operation

- within the range of the rotating machine parts

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be avoided.

These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered parts of the rotating saw

blade.

- Risk of injury when changing the blade.

- Risk of squeezing fingers when opening the guards.

- Health hazards caused by breathing dust developed when sawing

wood, especially oak and beech.

Package contents

The package contains:

1 Partly assembled machine

1 Table

1 Rip fence

1 Box spanner 8 mm

1 Pack containing:

1 Table insert

2 Blade guide blocks 45°

2 Blade guide blocks 90°

3 Coach bolts M8 x 60

4 Hex nuts M8

8 Washers D8

2 Washers D6

1 Hex bolt M8 x 60

4 Hex bolts M8 x 20

2 Hex bolts M6 x 65

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW739 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW739 T 2 Manual

Product: