Manual DeWalt DW729KN (page 34 of 128) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546568

Zoom out

Zoom in

1/128

ENGLISH

6. Firmly tighten all fasteners.

7. Tilt the assembly to upright position.

WARNING: The machine must be level and stable at all

times.

IMPORTANT: Assistance may be required to lower and raise

assembly.

MOUNTING THE TABLE EXTENSION (FIG. 1, 5–12)

Figure 5 shows the correct position of the triangular supports. The

supports are mounted using M8 x 20 bolts and corresponding nuts and

with D8 flat washers at the front, but not at the rear.

1. Mount the triangular supports (z) with the flat side of the support

facing the operator.

2. Mount the straight supports (aa) to the flat side of the triangular

support (z).

3. Fit the two table extensions (t) to the supports with M8 x 25 bolt,

washer and nut (fig. 6).

4. Firmly tighten all fasteners.

5. Check that the table extensions are flush with the fixed table top

and securely hand tighten the bolts.

WARNING: The table extensions and the fixed table top

MUST be flush.

6. Insert 3 dowels into the small, left fence (h1) and 3 dowels into the

larger right fence (h2) (fig. 7).

7. Align the left fence dowels with the left side holes in the fixed table

top and firmly press together (fig. 8).

8. Repeat with the right fence.

9. Align the back, left table strip (s1) with the left fence dowels and

firmly press together (fig. 9). Tighten the table clamp (ee) with

socket wrench (fig. 10).

10. Insert a M8 x 25 screw and D8 washer into the back, left table strip

and securely tighten (fig. 11, 12).

11. Repeat for back right table strip.

MOUNTING DUST SHROUD (FIG. 13, 14)

1. Fit the dust port in position back to the column base.

2. Insert 3 M8 x 16 screws and D8 washers into the dust port and

base holes.

3. Tighten all with 3 M8 nuts using 13 mm socket wrench and open

key spanner.

MOUNTING THE CABLE SUPPORT (FIG. 15, 16)

1. Remove the cross head screw (ff).

2. Mount the cable support (gg) and refit the cross head screw.

3. Remove the cable clamp (ii) located on the arm and reattach

holding the cables in place.

WARNING: Allow for the arm movement in horizontal and

vertical direction.

MOUNTING SWITCH BOX (FIG. 17)

DW728KN

The switch box (f) is mounted directly behind the right side of the

base. The switch box also contains the electronic brake and overload

protector.

1. From the inside of the base insert the four screws (ss) through the

base and into the four holes in the switch.

2. Tighten all fasteners.

DW729KN

The switch box (f) is mounted on a bracket which must be fitted to the

left-hand side leg using the fasteners on the bracket. The switch box

also contains the electronic brake, overload protector and an isolating

switch (w).

1. Fit the bracket in the holes in the left-hand side leg.

2. Tighten all fasteners.

MOUNTING THE SAW BLADE (FIG. 1, 18–25)

1. Ensure that the arm position is at 0˚ and raise the arm (m) to the

upper postion (fig. 1).

2. Tilt motor as follows:

a. Unlock the lever (cc, fig. 18)

b. Pull out the bevel latch (a4, fig. 19) , tilt the motor head (dd) as

shown for optimum access (fig. 20) and lock with the lever (cc,

fig. 21).

3. Loosen the guard screw (kk, fig. 22) and lift the guard (d) out of the

way (fig. 23).

4. Hold the flange (mm) in place with the pin wrench (hh) and turn the

blade screw (ll) clockwise using the 6 mm hex wrench (jj). Remove

the blade screw (ll), external flange (mm) and the blade (oo)

(fig.24,25).

5. To assemble the new blade repeat the steps in the opposite order.

6. The head is ready for cutting

WARNING: The teeth of a new blade are very sharp and

can be dangerous.

WARNING: The direction of rotation is indicated by the

arrow on the motor.

WARNING: Make sure that the washer of the arbour nut is

against the outer flange.

CHECKING THAT THE ARM IS PARALLEL TO THE TABLE TOP (FIG. 1, 26)

1. Lower the blade (oo) until it only just touches the fixed table top (e).

2. Release the mitre latch lever (j) and the mitre clamp lever (k).

3. Extend the blade forward past the fence then swing arm so that

the blade skims the table top across its width.

4. Repeat this procedure with the blade in rear position and adjust the

rear bolt if required.

CHECKING THAT THE BLADE IS PERPENDICULAR TO THE TABLE TOP

(FIG. 27–28)

1. Bring the arm back to central position.

2. Place a steel square (rr) against the blade body (fig. 27).

3. If adjustment is required, proceed as follows:

a. Remove the bevel pointer disk (tt, fig. 27) by loosening the two

screws (uu).

b. Loosen the hex screw (ww).

c. Loosen the lock nuts (v v) on either side of the bevel scale (u)

(fig. 28)

d. Using a hex wrench adjust the unlocked screws (pp) until the

blade is flat against the square.

4. Firmly tighten all fasteners.

WARNING: It is particularly important to tighten the central

hex screw.

5 Replace the bevel pointer disk (tt) (fig. 27).

CHECKING THAT THE CROSSCUT TRAVEL IS PERPENDICULAR TO THE FENCE

(FIG. 29, 30)

1. Lock the blade in front of the fence (fig. 29).

2. Place a square (rr) on a piece of board and against the fence and

just touching the blade as shown.

3. Pull the blade towards you to check that the blade traverses

parallel to the square.

4. If adjustment is required, proceed as follows:

a. Loosen the mitre latch lever (j) and release the mitre clamp lever

(k) (fig. 30).

b. Loosen the two adjustment screws (qq).

5. To adjust the arm to the left, loosen the stud on the right-hand side

of the mitre latch lever (j) and tighten the opposite stud.

6. To adjust the arm to the right, loosen the stud on the left-hand side

of the mitre latch lever (j) and tighten the opposite stud.

7. Proceed in small steps and check the adjustment after each step

with the levers (j) and (k) engaged.

WARNING: Do not overtighten the studs.

8. Tighten the adjustment screws (qq).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW729KN in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW729KN Manual

Product: