Manual DeWalt DW729KN (page 32 of 128) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546568

Zoom out

Zoom in

1/128

ENGLISH

• Before use, ensure the guards, brake, automatic return and locking

devices are functioning properly. Do not use the machine if these

devices are defective.

• When sawing a round workpiece ALWAYS use suitable jig or prism

to prevent rotation of the workpiece.

• Do not force the cutting action. (Stalling or partial stalling of the

motor can cause major damage.) Allow the motor to reach full

speed before cutting.

• Do not lift the machine by its worktable.

• Do not cut ferrous metals, non-ferrous metals or masonry.

• Do not apply lubricants to the blade when it is running.

• Do not place either hand in the blade area when the saw is

connected to the power source.

• Do not reach around behind the saw blade when in use.

• Do not place hands closer than 150 mm from the saw blade while

cutting.

• Do not use damaged or cracked saw blades.

• Replace the fence if damaged and/or no longer offers proper

support. The fence needs to be replaced periodically.

• ALWAYS ensure safe operation. The radial arm saws needs to be

fixed to the floor with diameter 8 mm bolts with a minimum length

of 80 mm.

WARNING! When cutting round workpiece it is necessary

to secure the workpiece against rotation by using jig or

holder.

• Do not use the machine in locations where the temperature may

reach -5˚ or 40˚ C. Suitable temperature is 20˚ C.

• Operators shall be instructed on factors influencing exposure to

noise (e.g. use of saw blade designed to reduce the emitted noise

and machine maintenance). Report faults in the machine, including

guards or saw blade, as soon as they are discovered. Ensure the

operator is adequately trained in use, adjustment and operation of

the machine.

• Connect the machine to a dust collection device when sawing

wood. Always consider factors which influence exposure of dust

such as:

– Type of material to be machined (chip board produces more

dust than wood).

– Correct adjustment of saw blade.

– Ensure that the local extraction as well as hoods, baffles and

chutes are properly adjusted.

• Always wear working gloves when servicing the machine, handling

rough workpieces or changing the saw blade.

• If a voltage failure occurs under idle condition, release the handle

immediately ensuring the saw head moves automatically back to its

rest position.

WARNING! Defect electrical wiring needs to be replaced

immediately.

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting or

changing set-ups or when making repairs. Be sure the

switch is in the OFF position An accidental start-up can

cause injury.

• Report the failure and mark the machine in suitable form to prevent

other people from using the defective machine.

• When the saw blade is blocked due to abnormal feed force during

cutting, turn the machine off and disconnect it from power supply.

Remove the workpiece and ensure that the saw blade runs free.

Turn the machine on and start new cutting operation with reduced

feed force.

Residual Risks

The following risks are inherent to the use of radial arm saws:

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be

avoided.

These are:

– Injuries caused by touching rotating parts.

– Impairment of hearing.

– Risk of accidents caused by the uncovered parts of the rotating

saw blade.

– Risk of injury when changing the blade.

– Risk of squeezing fingers when opening the guards.

– Health hazards caused by breathing dust developed when sawing

wood, especially oak, beech and MDF.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

When the power cord is damaged disconnect the plug

from the power source immediately.

Always disconnect the plug before making any

adjustments or perform service/maintenance.

Package Contents

The package contains:

1 Partly assembled radial arm saw

2 Table strips (1 right,1 left)

2 Fences (1 right, 1 left)

2 Table extensions (1 right, 1 left)

DW728KN: 1 Switch box with electronic brake

DW729KN: 1 SA switch box with electronic brake, overload protector

and main switch disconnector

1 Dust shroud

1 Box containing:

1 legstand

(4 legs, 1 SA height adjustment crank, 3 M8 x 25)

1 Instruction manual

1 Exploded drawing

3 Skinpacks

1 Skinpack containing:

12 D10 flat washers

12 M10 nuts

12 socket head screws M10 x 20

1 Skinpack containing:

4 Triangular supports (2 right, 2 left)

4 Straight supports

6 wood inserts

10 M8 x 25 bolts (aluminium)

19 M8 x 20 bolts

3 D8 (external diameter is 24 mm) washers

26 D8 flat washers

27 nuts M8

1 Skinpack containing:

1 rubber insert

6 hex wrenches (3, 4, 5, 6, 8 & 10 mm)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW729KN in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW729KN Manual

Product: