Manual DeWalt DW721KN T 2 (page 36 of 128) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546511

Zoom out

Zoom in

1/128

ENGLISH

WARNING: Do not overtighten the studs.

8. Tighten the locknuts (v v).

9. Adjust the pointer (xx) on the mitre scale (yy) so that it registers 0°

(fig. 42).

Blade Guard Assembly (ﬁ g. 43)

The blade guard is a multifunctional assembly which offers the following

safety features:

– Front guard (c) and spring-held rear guard (d) for full blade

protection.

– Dust extraction adapter (a1).

– Adjustable finger guard (a2) for use when cross-cutting.

BEVEL SCALE (FIG. 44)

Check that the bevel scale (u) reads 0˚ when positioned for a vertical

cut.

If required, loosen the screws (uu) and adjust the pointer to 0˚.

MITRE SCALE (FIG. 42)

Check that the mitre scale (yy) reads 0˚ when positioned for a vertical

cut.

Adjust the pointer (xx) to register 0˚ using the screw (zz).

The arm has preset positions at 45˚ left and right and at 0˚.

OPERATION

Instructions for Use

WARNING:

• Always observe the safety instructions and applicable

regulations.

• Ensure the material to be sawn is firmly secured in place.

• Apply only a gentle pressure to the tool and do not exert

side pressure on the saw blade.

• Avoid overloading.

WARNING:

• Install the appropriate saw blade. Do not use excessively

worn blades. The maximum rotation speed of the tool

must not exceed that of the saw blade.

• Do not attempt to cut excessively small pieces.

• Allow the blade to cut freely. Do not force.

• Allow the motor to reach full speed before cutting.

• Make sure all locking knobs and clamp handles are tight.

• Never run the machine without the guards in place.

• Never lift the machine by the table top.

• Always check that there is a suitable slot in the table top.

• Always refer to figure L to check the fence position and

type.

The attention of UK users is drawn to the “woodworking machines

regulations 1974” and any subsequent amendments.

SWITCHING ON AND OFF (FIG. 1)

The on/off switch of your radial arm saw offers multiple advantages:

– No-volt release function: should the power be shut off for

some reason, the switch has to be deliberately reactivated.

– Motor overload protection device: in case of motor overload,

the power supply to the motor will be cut off. If this happens, let

the motor cool for 10 minutes and then press the reset button.

– Braking system: after switching off, the braking system will

stop the saw blade within 10 seconds.

– The switch has hold-to-run functions only.

To switch the machine on, press the green actuator (a) in the handle (b).

When the actuator is released the machine stops automatically.

MAKING A TRIAL CUT (FIG. 1)

1. With the mitre latch lever (j) engaged, lock the mitre clamp lever (k)

so that the blade is positioned for a straight 0° cross-cut.

2. Lower the arm until the blade almost touches the table top.

3. Place the workpiece against the front of the fence.

4. Switch on and lower the arm to allow the blade to cut a shallow

groove in the table surface.

5. Pull the blade towards you so that it cuts a vertical slot in the

wooden fence and through the workpiece.

6. Return the blade back to rest position and switch off.

7. Check that the cut is a true 90° in all planes and adjust if required.

Basic Saw Cuts (ﬁ g. 45–53)

WARNING: The teeth of a new blade are very sharp and

can be dangerous.

CROSS-CUTTING (FIG. 45)

1. Set the radial arm at right angles to the fence.

2. Engage the mitre latch lever (j) in 0° position and tighten the mitre

clamp lever (k).

3. Lower the blade.

4. Adjust the finger guard (a2) so that it just clears the workpiece.

5. If there is no slot in the table top, cut one as described above.

6. Hold the workpiece against the fence, keeping your fingers well

away from the path of the blade.

7. Switch on and slowly pull the blade through the fence and the

workpiece.

8. Return the blade to rest position and switch off.

MITRE CUTS (FIG. 46, 47)

1. Release the mitre latch lever (j) and the mitre clamp lever (k).

2. Swing the arm to the required angle on the mitre scale.

3. For 45° left or right, engage the mitre latch lever (j) and lock with

the mitre clamp lever (k).

4. For intermediate angles, use the mitre clamp lever only.

5. Proceed as for cross-cutting.

BEVEL CUTS (FIG. 45, 48)

1. Set the arm as for a 0° cross-cut.

2. Raise the blade well above the table surface.

3. Release the bevel clamp lever (a3) and pull out the bevel latch (a4).

4. Tilt the motor to the required angle on the bevel scale (u).

5. For 45° right, engage the bevel latch (a4) and lock with the bevel

clamp lever (a3).

6. For intermediate angles, use the bevel clamp lever only.

7. Proceed as for a vertical cross-cut.

COMPOUND MITRE (FIG. 47)

This cut is a combination of a mitre and a bevel cut.

1. Set the required bevel angle.

2. Swing the arm to the required mitre position.

3. Proceed as for mitre cuts.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

NOTE: No service is needed on mechanical brake.

IMPORTANT: Replace the fixed table top and fence when worn.

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting or

changing set-ups or when making repairs. Be sure the

switch is in the OFF position. An accidental start-up can

cause injury.

WARNING: if the saw blade is worn replace it with a new

or re-sharpened blade.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW721KN T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW721KN T 2 Manual

Product: