Manual DeWalt DW721KN T 2 (page 34 of 128) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546511

Zoom out

Zoom in

1/128

ENGLISH

Description (ﬁ g. 1)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

a. On/off switch

b. Handle

c. Front guard

d. Lower guard

e. Fixed table top

f. Traverse rails

g. Leg

h1. Left fence (small)

h2. Right fence (large)

i. Dust shroud

j. Mitre latch lever

k. Mitre clamp lever

l. Height adjustment crank

m. Radial arm

n. End-cap

o. Cable

p. Dust outlet

q. Yoke assembly

r. Motor

s1. Left table strip

s2. Right table strip

t1. Left table extension

t2. Right table extension

u. Bevel scale

v. Roller head assembly

w. No-volt release switch

x. Electronic control box

INTENDED USE

The radial arm saw has been designed for professional woodworking.

This high precision machine can be easily and quickly set to crosscut,

bevel, mitre. For optimum safety, all major controls have both a latch

and a locking device. Also refer to the quick reference chart at the end

of the section. This saw is designed for use with a 300 mm diameter

carbide tip blade.

DO NOT use under wet conditions or in presence of flammable liquids

or gases.

The radial arm saw is a professional power tool.

DO NOT let children come into contact with the tool. Supervision is

required when inexperienced operators use this tool.

Electrical Safety

The electric motor has been designed for one voltage only. Always

check that the power supply corresponds to the voltage on the rating

plate.

If the supply cord is damaged, it must be replaced by a specially

prepared cord available through the DEWALT service organization.

Mains Plug Replacement

(U.K. & Ireland Only)

SINGLE-PHASE ONLY

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the new plug.

• Connect the blue lead to the neutral terminal.

• Connect the green/yellow lead to the earth terminal.

WARNING: Follow the fitting instructions supplied with

good quality plugs. Recommended fuse: 13 A.

WARNING: This product must be earthed. Always check

that the power supply corresponds to the voltage on the

rating plate.

Contact a qualified electrician if a new CEE 16 A industrial plug needs

to be fitted.

Using an Extension Cable

An extension cord should not be used unless absolutely necessary.

Use an approved extension cable suitable for the power input of your

machine (see technical data). When using a cable reel, always unwind

the cable completely. The maximum cable length is 30m.

SINGLE-PHASE MACHINES

Use an approved 3-core extension cable suitable for the power input

of this machine (see technical data). The minimum conductor size is

1.5mm².

THREE-PHASE MACHINES

Please ensure the cable is provided with CEE 16A industrial plug/

coupler 5 poles (neutral must be connected) according to IEC 60309.

Voltage Drops

Inrush currents cause short-time voltage drops. Under unfavourable

power supply conditions, other equipment may be affected.

If the system impedance of the power supply is lower than 0.25 Ω,

disturbances are unlikely to occur.

Sockets used for these machines shall be fused with 16 Amperes

cut-out with an inert characteristic.

ASSEMBLY AND ADJUSTMENT

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting or

changing set-ups or when making repairs. Be sure the

switch is in the OFF position. An accidental start-up can

cause injury.

WARNING: For optimum performance of your saw, it is of

vital importance to follow the procedures in the paragraphs

below.

Set Up

MOUNTING THE HEIGHT ADJUSTMENT CRANK (FIG. 1, 2)

1. Apply the height adjustment crank (l) with the cross head screw.

NOTE: Automatic return arm may need to be moved to allow

height adjustment.

2. Raise the height adjustment crank high enough to provide

clearance for removal of various elements under the motor.

ASSEMBLING THE LEGSTAND (FIG. 1, 3, 4)

The legstand components and fasteners are packed separately.

1. Remove all parts from the package.

2. Lock the arm using the mitre clamp lever (k).

3. Tilt the machine carefully from the pallet until the rear of the column

is resting on the floor.

4. Place a piece of wood (y) under the edge of the table (fig.3).

5. Assemble the legs (g) as shown using the nuts, bolts and flat

washers provided.

NOTE: Do not tighten.

6. Mount the traverse rails (f) (fig. 4).

7. Firmly tighten all fasteners.

8. Tilt the assembly to upright position.

WARNING: The machine must be level and stable at all

times.

IMPORTANT: Assistance may be required to lower and raise

assembly.

MOUNTING THE AUTOMATIC RETURN (FIG. 1, 5–10)

1. The automatic return comes partially assembled as shown in

figure 5.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW721KN T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW721KN T 2 Manual

Product: