546159

DeWalt DW716E Manual

30
Zoom out
Zoom in
Previous page
1/132
Next page
28
4. Keep other persons away.
Do not let persons, especially children, not involved in the work, touch
the tool or the extension cord and keep them away from the work area.
5. Store idle tools.
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate to which it was intended.
7. Use the right tool.
Do not force small tools to do the job of a heavy duty tool. Do not use
tools for purposes not intended; for example do not use circular saws
to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Non-skid footwear is recommended when working
outdoors. Wear protective hair covering to contain long hair.
9. Use protective equipment.
Always use safety glasses. Use a face or dust mask if working
operations create dust or flying particles. If these particles might be
considerably hot, also wear a heat-resistant apron. Wear ear protection
at all times. Wear a safety helmet at all times.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust extraction and
collecting equipment, ensure these are connected and properly used.
11. Do not abuse the cord.
Never yank the cord to disconnect it from the socket. Keep the
cord away from heat, oil and sharp edges. Never carry the tool by its
cord.
12. Secure work.
Where possible use clamps or a vice to hold the work. It is safer than
using your hand and it frees both hands to operate the tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect
tools periodically and if damaged have them repaired by an authorized
service facility. Keep handles and switches dry, clean and free from oil
and grease.
15. Disconnect tools.
When not in use, before servicing and when changing accessories such
as blades, bits and cutters, disconnect tools from the power supply.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that adjusting keys and wrenches are
removed from the tool before operating the tool.
17. Avoid unintentional starting.
Do not carry the tool with a finger on the switch. Be sure that the tool is
in the “off” position before plugging in.
18. Use outdoor extension leads.
Before use, inspect the extension cable and replace if damaged.
When the tool is used outdoors, use only extension cords intended for
outdoor use and marked accordingly.
19. Stay alert.
Watch what you are doing. Use common sense. Do not operate the tool
when you are tired or under the influence of drugs or alcohol.
20. Check for damaged parts.
Before use, carefully check the tool and mains cable to determine
that it will operate properly and perform its intended function. Check
for alignment of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or
replaced by an authorized service centre unless otherwise indicated
in this instruction manual. Have defective switches replaced by an
authorized service centre. Do not use the tool if the switch does not
turn it on and off. Never attempt any repairs yourself.
WARNING! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
21. Have your tool repaired by a qualified person.
This electric tool complies relevant safety rules. Repairs should only be
carried out by qualified persons using original spare parts; otherwise this
may result in considerable danger to the user.
Additional Safety Rules for Mitre Saws
• The machine is provided with a special configured power supply cord
which can only be replaced by the manufacturer or its authorised
service agent.
• Do not use the saw to cut other materials than those recommended by
the manufacturer.
• Do not operate the machine without guards in position, or if guards do
not function or are not maintained properly.
• Ensure that the arm is securely fixed when performing bevel cuts.
• Keep the floor area around the machine level, well-maintained and free
of loose materials, e.g., chips and cut-offs.
• Use correctly sharpened saw blades. Observe the maximum speed
mark on the saw blade.
• Make sure all locking knobs and clamp handles are tight before starting
any operation.
• Never place either hand in the blade area when the saw is connected to
the electrical power source.
• Never attempt to stop a machine in motion rapidly by jamming a tool or
other means against the blade; serious accidents can occur.
• Before using any accessory consult the instruction manual.
The improper use of an accessory can cause damage.
• Use a holder or wear gloves when handling a saw blade.
• Ensure that the saw blade is mounted correctly before use.
• Make sure that the blade rotates in the correct direction.
• Do not use blades of larger or smaller diameter than recommended. For
the proper blade rating refer to the technical data. Use only the blades
specified in this manual, complying with EN 847-1.
• Consider applying specially designed noise-reduction blades.
• Do not use HSS blades.
• Do not use cracked or damaged saw blades.
• Do not use any abrasive discs.
• Never use your saw without the kerf plate.
• Raise the blade from the kerf in the workpiece prior to releasing the switch.
• Do not wedge anything against the fan to hold the motor shaft.
• The blade guard on your saw will automatically raise when the arm is
brought down; it will lower over the blade when head lock up release
lever (11) is pushed.
• Never raise the blade guard manually unless the saw is switched off.
The guard can be raised by hand when installing or removing saw
blades or for inspection of the saw.
• Check periodically that the motor air slots are clean and free of chips.
• Replace the kerf plate when worn.
• Disconnect the machine from the mains before carrying out any
maintenance work or when changing the blade.
• Never perform any cleaning or maintenance work when the machine is
still running and the head is not in the rest position.
• When possible, always mount the machine to a bench.
• If you use a laser to indicate the cutting line, make sure that the laser is
of class 2 according to EN 60825-1. Do not replace a laser diode with
a different type. If damaged, have the laser repaired by an authorised
repair agent.
• The front section of the guard is louvered for visibility while cutting.
Although the louvers dramatically reduce flying debris, they are
openings in the guard and safety glasses should be worn at all times
when viewing through the louvers.
ENGLISH
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW716E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW716E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info