Manual DeWalt DW711 (page 27 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

545006

Zoom out

Zoom in

1/100

20 en - 6

ENGLISH

Bevel cross-cut (fig. A1, G1 & M)

Bevel angles can be set from 0° to 48° to the left. Bevels up to 45° can be

cut with the head set between zero and a maximum of 45° mitre position

right or left (fig. M).

• Loosen the bevel clamp handle (12) and set the bevel as desired (fig. A1).

• Use the 45°/48° adjustment handle (50) if required (fig. G1).

• Tighten the bevel clamp handle firmly.

• Proceed as for a vertical straight cross-cut.

Sawing in the bench mode

Ripping (fig. A1, A2, C1, D1 & N)

• Set the blade to the vertical position.

• Loosen the table locking knobs, both main (37) (fig. D1) and additional

(3) (fig. A1), but do not take off. Set the depth of cut by sliding the table

(14) (fig. A2) up or down. The correct position is to have the tips of

three teeth above the top surface of the wood.

• Loosen the sliding fence locking knob (35) (fig. C1) and slide the sliding

fence front or rear in order to support as much of the workpiece as

possible. At least the rear end of the fence should be level with the

front of the riving knife.

• Lock the table locking knobs tightly.

• Ensure the plastic guard plate (18) is in fixed position (fig. A2).

• Ensure that the rip fence is parallel with the blade.

• Set the rip fence for the width of cut required by using the scale let into

the front of the table. Set the sliding rip fence to the required position.

• Switch on the machine.

• Slowly feed the workpiece underneath the front of the upper blade

guard, keeping it firmly pressed against the rip fence. Allow the teeth to

cut and do not force the workpiece through the blade. The blade

speed should be kept constant.

• Remember to always use the push stick (57) (fig. N).

• After completing the cut, switch off the machine.

Optional accessories

Dust extraction

A dust extraction kit (DE7779) is available for optimal dust extraction.

Clamping the workpiece (fig. A3)

• In most cases, the action of the blade is sufficient to hold the material

firmly against the fence.

• If the material has a tendency to lift or come forward from the fence,

preferably use the optional material clamp (23).

• Always use the clamp if cutting non-ferrous metals.

Sawing short workpieces (fig. A3)

It is advisable to use the length stop for short workpieces (27) both for batch

sawing and for short individual workpieces of different lengths. The length

stop can only be used in conjunction with a pair of optional guide rails (21).

Sawing long workpieces (fig. A3)

Always support long workpieces.

Figure A3 shows the ideal configuration for sawing long workpieces when

the saw is used free-standing (all items available as an option).

These items (except the legstand and the material clamp) are required

both on the infeed and the outfeed side:

- Legstand (28) (supplied with mounting instructions).

- Guide rails (500 or 1,000 mm) (21).

- Stands (25) to support the guide rails. Do not use the stands to

support the machine! The height of the stands is adjustable.

- Material support plates (22).

- Table end plate (20) for supporting the rails (also when working on

an existing bench).

- Material clamp (23).

- Swivelling stop (24).

• Place your saw on the legstand and fit the guide rails.

• Firmly screw the material support plates (22) to the guide rails (21).

• Install the table end plates (20).

• Install the swivelling stop (24) to the rear rail.

• Use the swivelling stop (24) to adjust the length of medium and long

workpieces. It can be adjusted sideways or swung out of the way

when not in use.

Using the roller table (fig. A3 & A5)

The roller table (33) makes the handling of large and long pieces of wood

very easy (fig. A5). It can be connected either to the left or to the right of the

machine. The roller table requires the use of the optional legstand (fig. A3).

Assemble the roller table following the instructions supplied

with the legstand.

• Replace the short support bars provided with the legstand with the

irregular rails from the table on the side the table is to be used.

• Follow all instructions provided with the roller table.

Range of saw blades available (recommended blades)

Type of blade Blade dimensions Usage

DT1529 series 40 260x30x24 For cutting wood along the grain,

block board, plywood and MDF.

Coarse cut.

DT1531 series 40 260x30x48 For cutting wood along the grain,

block board, plywood and MDF.

Medium cut.

DT1530 series 40 260x30x80 For cutting wood, wood products,

plastics and aluminium. Fine cut.

DT1735 series 60 260x30x24 For cutting wood along the grain,

block board, plywood and MDF.

Coarse cut.

DT1736 series 60 260x30x48 For combination cutting in wood, block

board, plywood and MDF. Medium cut.

DT1737 series 60 260x30x80 For cutting wood, wood products

and plastics. Not for aluminium!

Fine cut.

Consult your dealer for further information on the appropriate accessories.

Transporting

To facilitate carrying, pull down the head and push in the head lock down

knob (13).

Maintenance

Your DEWALT Power Tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Unwanted tools and the environment

Take your tool to an authorized DEWALT repair agent where it will be

disposed of in an environmentally safe way.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW711 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW711 Manual

Product: