Manual DeWalt DW711 (page 26 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

545006

Zoom out

Zoom in

1/100

en - 5 19

ENGLISH

If the saw blade is not exactly at 90° to the fence:

• Loosen the two screws (53) and move the scale/head assembly left or

right until the blade is at 90° to the fence as measured with the square

(fig. H4).

• Lock the mitre clamping knob (9) (fig. A1).

• Tighten the two screws (53) (fig. H4).

Make sure the rear edge of the mitre scale keeps in contact

with the two location lugs (54) at all times.

Adjusting the riving knife (fig. A1, D1, J1 & J2)

The correct position is for the top of the riving knife (31) to be no more

than 2 mm below the highest tooth of the blade and the body of the radius

to be a maximum of 5 mm from the tips of the saw blade teeth (fig. J1).

• Loosen the table locking knobs, both main (37) (fig. D1) and additional (3)

(fig. A1), but do not take them off.

• Use the Allen key to remove the screw (55) from the rear table column

(fig. D1). Take the nut and washer off the other end of the screw.

• Remove the table.

• The riving knife (31) (fig. J1) is fastened by a large Allen screw (56)

towards the rear of the right-hand side under the table (fig. J2).

• To adjust the riving knife, loosen the Allen screw which allows both the

bracket to rotate and the riving knife to move up and down.

• After loosening, rotate the bracket and slide the knife either up or down

until the correct position is attained.

• Retighten the screw (56) firmly (fig. J2).

• Replace the table and replace the Allen screw assembly (55) (fig. D1).

• Set the table to the proper height needed.

• Tighten the table locking knobs (fig. A1 & D1).

Lubrication

This machine requires no additional lubrication. The bearings of the motor

are pre-lubricated and watertight.

• Avoid using oil or grease as this can cause clogging with sawdust and

chips and create problems.

• Clean the parts subject to accumulation of sawdust and chips

periodically with a dry brush.

Instructions for use

• Always observe the safety instructions and applicable regulations.

The attention of UK users is drawn to the “woodworking

machines regulations 1974” and any subsequent amendments.

• Ensure the material to be sawn is firmly secured in place.

• Apply only a gentle pressure to the tool and do not exert side

pressure on the saw blade.

• Avoid overloading.

• Always remove the dust from the machine after using to

ensure the lower guard operates properly.

Prior to operation:

• Install the appropriate saw blade. Do not use excessively worn blades.

The maximum rotation speed of the tool must not exceed that of the

saw blade.

• Do not attempt to cut excessively small pieces.

• Allow the blade to cut freely. Do not force.

• Allow the motor to reach full speed before cutting.

• Make sure all locking knobs and clamp handles are tight.

Switching on and off (fig. A)

• To switch the machine on, press the on/off switch (1).

• To switch the machine off, press the on/off switch again.

Quality of cut

The smoothness of any cut depends on a number of variables, e.g. the

material being cut. Please see the chart below for the recommended saw

blades applications.

Ensure that the material does not creep while cutting; clamp it

securely in place. Always let the blade come to a full stop

before raising the arm. If small fibres of wood still split out at

the rear of the workpiece, stick a piece of masking tape on the

wood where the cut will be made. Saw through the tape and

carefully remove tape when finished.

Setting the mitre (fig. A1)

The mitre arm can be preset to 0°, 15°, 22.5°, 30° and 45° left and right.

It is also possible to set the mitre angle to 48°.

• Loosen the mitre clamping knob (8) and lift the positive stop lever (7)

to release the mitre arm (9).

• Move the arm to the required angle and lock it using the mitre clamping

knob (8).

• Align the mitre arm as shown in fig. H1 - H3 by moving the edge of the

arm to the required mark on the scale.

When mitre cutting, ensure that the off-cut is not wedged

between the blade and the fence, i.e. the off-cut angle is greater

than 90° to avoid that the off-cut is picked up by the blade.

Setting the bevel (fig. G1)

• Set the 45°/48° adjustment handle (50) to the required position.

- Out = 48°

- In = 45°

• Loosen the bevel clamp handle (12) and bevel the head to the left;

there are marked positions at 0°, 15°, 30°, 33.85° and 45°.

• Hold the head firmly and do not allow it to fall.

• Holding the head, lock the bevel clamp handle securely.

Sawing in mitre saw mode

It is dangerous to operate without guarding. Guards must be in position

when sawing.

Ensure that aluminum workpieces are clamped securely.

Vertical straight cross cut (fig. K)

• Loosen the mitre clamping knob (8) and lift the positive stop lever (7)

upwards.

• Engage the mitre latch at the 0° position and tighten the mitre clamping

knob.

• Place the wood to be cut against the fence (11). Take hold of machine

handle and press in the head lock-up release lever (2).

• Pull down the head approximately 10 mm and release the lock-up lever.

• Switch on the machine and depress the head to allow the blade to cut

through the workpiece and enter the table slot.

• Allow the blade to cut freely. Do not force.

• After completing the cut, switch off the machine and return the head to

its upper rest position.

Vertical mitre cross-cut (fig. K & L)

• Loosen the mitre clamping knob (8) and lift the positive stop lever (7)

upwards (fig. K).

• Move the head left or right to the required angle. There are preset

positions at 15°, 22.5°, 30° and 45° (fig. L).

• If any intermediate angle or 48° is required hold the head firmly and

lock by tightening the mitre clamp knob.

• Always ensure that the mitre clamp knob is locked tightly before

cutting.

• Proceed as for a vertical straight cross-cut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW711 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW711 Manual

Product: