544991
28
Zoom out
Zoom in
Previous page
1/116
Next page
en - 5 21
ENGLISH
Bevel stop adjustment (fig. H1 - H4)
Adjusting the bevel stop and pointer to 0° (fig. H1 & H2)
Place the saw in the 0° bevel position (fig. H1).
Push the head fully back and tighten the rail lock knob (20) (fig. H2).
Place a set square (36) on the table and up against the blade (33) (fig. H1).
Do not touch the tips of the blade teeth with the square.
If adjustment is required, proceed as follows:
Loosen the bevel lever (11) (fig. H2).
Press the mitre arm to the right, against the 0° bevel stop.
Adjust the screw (43) until the blade is perpendicular to the base.
Tighten the lever (11) securely.
Make sure the bevel pointer (44) indicates exactly 0°.
If not, loosen the screw (45), set the pointer to 0° and tighten the screw.
Adjusting the bevel stop to 45° left or right (fig. H2 - H4)
First, adjust the 0° bevel angle.
- Left 45° bevel angle
Loosen the bevel lever (11) and tilt the head to the left (fig. H3).
If the pointer (44) does not indicate exactly 45°, turn the screw (12)
on the left side until the pointer reads 45° (fig. H2).
- Right 45° bevel angle
Depress the bevel stop override button (11A) and tilt the head to the
right (fig. H4).
If the pointer does not indicate exactly 45°, turn the screw (43A) on
the lower right side until the pointer reads 45° (fig. H3).
Adjusting the fence (fig. A1 & J)
The fences (3) and (7) can be adjusted to provide clearance, allowing the
saw to bevel to a full 48°.
Loosen the fence adjustment knob (23) and slide the fence to the
required position (fig. J).
Make a dry run with the saw turned OFF and check for clearance.
Adjust the fence to be as close to the blade as practical to provide
maximum workpiece support, without interfering with the up and down
movement of the arm.
Firmly tighten the fence adjustment knob (23).
Move the fences back after the cut has been accomplished.
When bevelling to the right, it may be necessary to remove the
right fence (3) (fig. A1)
Rail guide adjustment (fig. K)
Regularly check the rails for clearance.
To reduce clearance, gradually rotate the set screws (19) clockwise
while sliding the saw head back and forth.
Instructions for use
Always observe the safety instructions and applicable regulations.
The attention of UK users is drawn to the “woodworking
machines regulations 1974” and any subsequent amendments.
Prior to operation:
Make sure the guards have been mounted correctly. The saw blade
guard must be in closed position.
Make sure the saw blade rotates in the direction of the arrow on the blade.
Switching ON and OFF (fig. L)
To run the tool, press the ON/OFF-switch (1).
To stop the tool, release the switch.
There is no provision for locking the switch ON, but a hole (47) is
provided for insertion of a padlock to lock the saw OFF.
Basic saw cuts (fig. A1, A2, M1 - M3)
Vertical straight cross cut (fig. A1 & A2)
Loosen the mitre lever (4) and squeeze the mitre latch (5) upwards.
Engage the mitre latch at the 0° position and tighten the lever (4).
Place the wood to be cut against the fences (3) and (7).
Take hold of the operating handle and depress the head lock up
release lever (50) to release the head.
With the rail lock knob tightened, switch the saw ON.
Lower the head to allow the blade to cut through the workpiece and
enter the kerf plate (25).
After completing the cut, release the switch, let the blade come to a full
stop and return the head to its upper rest position.
Workpieces larger than 50 x 100 mm (fig. M1)
The guide rail allows cutting larger workpieces using an out-down-back motion.
Release the rail lock knob (20).
Pull the saw towards you, lower the saw into the workpiece and push it
back to complete the cut.
Proceed as described above.
Vertical mitre cross-cut (fig. M2)
Loosen the fence clamping knobs and adjust the fences.
Loosen the mitre lever (4) and squeeze the mitre latch (5) upwards.
Move the head left or right to the required angle.
Always ensure that the lever (4) is locked tightly before cutting.
Proceed as for a vertical straight cross-cut.
Bevel cuts (fig. M3, H2 & H4)
Loosen the fence clamping knobs (23) and adjust the fences (3) and (7).
Loosen the bevel lever (11) and set the required angle.
Tighten the lever (11) firmly.
To bevel to the right, depress the bevel stop override button (11A).
Bevelling 48° to the left (fig. H2 & H3)
To set a bevel angle greater than 45°, the bevel stop must be adjusted.
Loosen the bevel lever (11) and tilt the head to the left.
Turn the screw (12) until the pointer (44) indicates the desired bevel
angle (up to 48°).
Bevelling 48° to the right (fig. H2 - H4)
To set a bevel angle greater than 45°, the bevel stop must be adjusted.
Depress the bevel stop override button (11A) and tilt the head to the
right.
Turn the screw (43A) until the pointer (44) indicates the desired bevel
angle (up to 48°).
Quality of cut
The smoothness of any cut depends on a number of variables, e.g. the
material being cut. When smoothest cuts are desired for moulding and
other precision work, a sharp (60 tooth carbide) blade and a slower,
even cutting rate will produce the desired results.
Ensure that the material does not creep while cutting; clamp it
securely in place. Always let the blade come to a full stop
before raising the arm. If small fibres of wood still split out at
the rear of the workpiece, stick a piece of masking tape on the
wood where the cut will be made. Saw through the tape and
carefully remove tape when finished.
28


Need help? Post your question in this forum.

Forumrules
1

Forum

dewalt-dw708

Reset search

  • I have a DeWalt dw708 sliding compound miter saw. The bald is stuck in the up position. I am having a major brain fart, and can’t figure out how to unlock it, so it will lower. I’ve looked on line, and people point to an unlocking button on the side, or say there’s a button near the top. No button near the top on mine that I can see, and the button on the right side doesn’t seem to do anything. Help please? Submitted on 8-12-2021 at 01:36

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW708 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW708 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info