Manual DeWalt DW705 T 4 (page 30 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544979

Zoom out

Zoom in

1/116

en - 7 24

ENGLISH

For example, if you measure the corner of an 8 sided box, the protractor

will read 135°. To determine the proper mitre setting, divide the measured

angle by two. The proper mitre setting in this example is 67

/2.

Set this angle on the 90° scale.

Vernier scale (fig. U1 - U3)

Your saw is equipped with a vernier scale for added precision.

For settings that require partial degrees (

/4°,

/2°,

/4°), the vernier scale

allows you to accurately set mitre angles to the nearest

/4° (15 minutes).

To use the vernier scale follow the steps listed below.

• Align the desired vernier mark with the closest degree mark on the

mitre scale, as described below. The plastic vernier plate is inscribed

with marks for

/4°,

/2°,

/4° and 1°. Only the

/2° and the 1° are

numerically labelled.

As an example, assume that the angle you want to mitre is 24

/4° right.

• Turn OFF the Mitre Saw.

• Set the mitre angle to the nearest whole degree desired by aligning the

centre mark in the vernier scale, shown in fig. U1, with the whole

degree number etched in the mitre scale. Examine fig. U2 closely;

the setting shown is 24° right mitre. To set the additional

/4°, squeeze

the mitre arm lock and carefully move the arm to the right until the

/4°

vernier mark aligns with the closest degree mark on the mitre scale.

In this example, the closest degree mark on the mitre scale happens to

be 25°. Fig. U3 shows a setting of 24

/4° right mitre.

When mitring to the right:

- increase the mitre angle by moving the arm to align the appropriate

vernier mark with the closest mark on the mitre scale to the right.

- decrease the mitre angle by moving the arm to align the appropriate

vernier mark with the closest mark on the mitre scale to the left.

When mitring to the left:

- increase the mitre angle by moving the arm to align the appropriate

vernier mark with the closest mark on the mitre scale to the left.

- decrease the mitre angle by moving the arm to align the appropriate

vernier mark with the closest mark on the mitre scale to the right.

Cutting Base Mouldings (fig. V1 - V4)

Vertical position

• Always make a dry run without power before making any cuts.

Straight 90° cuts (fig. V1)

• Position the wood against the fence and clamp it in place as shown in

fig. V1.

• Turn the saw ON, allow the blade to reach full speed and lower the arm

smoothly through the cut.

45° mitre cuts (fig. V2)

• Position the moulding as shown in fig. V2.

• All cuts are made with the back of the moulding against the fence and

the bottom of the moulding against the base.

Inside corner

- Left side

• Mitre left 45°.

• Save the left side of the cut.

- Right side

• Mitre right 45°.

• Save the right side of the cut.

Outside corner

- Left side

• Mitre right 45°.

• Save the left side of the cut.

- Right side

• Mitre left 45°.

• Save the right side of the cut.

DW705 - Horizontal position using bevel (fig. V3 & V4)

Another method of making the cut is to make a 0° mitre, 45° bevel cut.

Your saw can cut a bevel 200 mm wide. All cuts are made with 45° bevel

and 0° mitre. All cuts are made with the back of the moulding laying flat on

the saw as shown in fig. V3 and V4.

Inside corner

- Left side

• Position the moulding with top of the moulding against the fence.

• Save the left side of the cut.

- Right side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the left side of the cut.

Outside corner

- Left side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the right side of the cut.

- Right side

• Position the moulding with top of the moulding against the fence.

• Save the right side of the cut.

Saw Blades

To obtain the stated cutting capacities, always use 305 mm saw blades

with 30 mm arbor holes.

Cutting non-ferrous metals

When cutting non-ferrous metals, the machine is only to be used to

perform vertical straight and mitre cross-cuts in the mitre saw mode.

We recommend that bevel and compound mitre cuts should not be

performed in non-ferrous metals. The machine is not to be used for cutting

ferrous metals.

• Always use a material clamp when cutting non-ferrous metals.

Make sure that the workpiece is clamped securely.

• Only apply saw blades that are qualified for cutting non-ferrous metals.

• When using lubricants, only apply wax or separation spray. Do not use

emulsions or similar fluids.

• Connect an FI or DI switch between machine and mains to avoid

residual risks caused by metal swarf.

The FI switch should comply with the following specifications:

rated voltage 230 V

rated current 16 A

reaction time < 15 ms

fusing current 30 mA

The DI switch should comply with the following specifications:

DIN VDE 0661

rated voltage 230 V

rated current 16 A

fusing current 30 mA

all-pole cutoff L+N+PE

PE monitoring

low-voltage release

Consult your dealer for further information on the appropriate accessories.

Cual es la pieza o como se llama. Donde acopla la hoja de sierra Submitted on 8-1-2022 at 00:55
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW705 T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW705 T 4 Manual

Product: