Manual DeWalt DW705 T 4 (page 29 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544979

Zoom out

Zoom in

1/116

0 5 10 15 20 25 30 35 40 45

ENGLISH

Ensure that the material does not creep while cutting; clamp it

securely in place. Always let the blade come to a full stop

before raising the arm. If small fibres of wood still split out at

the rear of the workpiece, stick a piece of masking tape on the

wood where the cut will be made. Saw through the tape and

carefully remove tape when finished.

Body and hand position (fig. Q1 - Q4)

Proper positioning of your body and hands when operating the Mitre Saw

will make cutting easier, more accurate and safer.

• Never place your hands near the cutting area.

• Place your hands no closer than 150 mm from the blade.

• Hold the workpiece tightly to the table and the fence when cutting.

Keep your hands in position until the trigger has been released and the

blade has completely stopped.

• Always make dry runs (without power) before finish cuts so that you

can check the path of the blade.

• Do not cross your hands as shown (fig. Q4).

• Keep both feet firmly on the floor and maintain proper balance.

• As you move the saw arm left and right, follow it and stand slightly to

the side of the saw blade.

• Sight through the guard louvres (60) when following a pencil line.

Clamping the workpiece (fig. V1 - V4)

Always use a material clamp when cutting non-ferrous metals.

• Whenever possible, clamp the wood to the saw.

• For best results use the clamp (31) made for use with your saw

(available from your dealer as an option). Clamp the workpiece to the

fence whenever possible. You can clamp to either side of the saw blade;

remember to position your clamp against a solid, flat surface of fence.

Support for long pieces (fig. B3)

• Always support long pieces.

• For best results, use the extension work support (29) to extend the

table width of your saw (available from your dealer as an option).

Support long workpieces using any convenient means such as saw-

horses or similar devices to keep the ends from dropping.

Cutting picture frames, shadow boxes & other four sided projects

(fig. R1 & R2)

Trim moulding and other frames

Try a few simple projects using scrap wood until you develop a “feel” for

your saw. Your saw is the perfect tool for mitring corners like the one

shown in fig. R1. The joint shown can be made using either bevel (DW705)

or mitre adjustment.

DW705 - Using bevel adjustment

The bevel for the two boards is adjusted to 45° each, producing a 90° corner.

The mitre arm is locked in the zero position. The wood is positioned with

the broad flat side against the table and the narrow edge against the fence.

Using mitre adjustment

The same cut can be made by mitring right and left with the broad surface

against the fence (fig. R2).

The two sketches (fig. R1 & R2) are for four side objects only. As the

number of sides changes, so do the mitre and bevel angles. The chart

below gives the proper angles for a variety of shapes, assuming that all

sides are of equal length. For a shape that is not shown in the chart,

divide 180° by the number of sides to determine the mitre or bevel angle.

23 en - 6

SET THIS MITER ANGLE ON SAW

SET THIS BEVEL ANGLE ON SAW

ANGLE OF SIDE OF BOX (ANGLE"A")

SQUARE BOX

6 SIDED BOX

No. of sides Angle mitre or bevel

4 45°

5 36°

6 30°

7 25.7°

8 22.5°

9 20°

10 18°

DW705 - Cutting Compound Mitres (fig. S1 & S2)

A compound mitre is a cut made using a mitre angle (fig. R2) and a bevel

angle (fig. R1) at the same time. This is the type of cut used to make

frames or boxes with slanting sides like the one shown in fig. S1.

If the cutting angle varies from cut to cut, check that the bevel

clamp knob and the mitre lock knob are securely tightened.

These knobs must be tightened after making any changes in

bevel or mitre.

• The chart shown below will assist you in selecting the proper bevel and

mitre settings for common compound mitre cuts. To use the chart,

select the desired angle “A” (fig. S2) of your project and locate that

angle on the appropriate arc in the chart. From that point follow the

chart straight down to find the correct bevel angle and straight across

to find the correct mitre angle.

• Set your saw to the prescribed angles and make a few trial cuts.

• Practice fitting the cut pieces together.

Example: To make a 4 sided box with 30 exterior angles

(angle “A”, fig. S2), use the upper right arc. Find 30 on the arc scale.

Follow the horizontal intersecting line to either side to get the mitre angle

setting on the saw (23). Likewise follow the vertical intersecting line to

the top or bottom to get the bevel angle setting on the saw. Always try

cuts on a few scrap pieces of wood to verify the settings on the saw.

Dual range mitre scale (fig. T1 & T2)

The mitre scale has two ranges of numbers for convenience, as shown in

fig. T1 & T2. One scale indicates 0° when the blade is square to the fence.

At this position the other scale reads 90°. The 0° scale (larger numbers

closer to the front edge) is used when calculating angles. To calculate the

proper mitre angle, divide 180° by the number of sides of the box or

frame. Refer to the previous chart for some examples. The 90° scale

(smaller numbers behind the 0° scale) is used when a corner of your box

or frame is measured with a protractor.

8 SIDED BOX

Cual es la pieza o como se llama. Donde acopla la hoja de sierra Submitted on 8-1-2022 at 00:55
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW705 T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW705 T 4 Manual

Product: