Manual DeWalt DW625E T 4 (page 24 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

546412

Zoom out

Zoom in

1/100

en - 5

ENGLISH

• For optimum ease of operation, the carriage

return can be adapted to the required depth of

cut by rotating or sliding the knurled nut (9).

• Loosen the clamping screw (15).

• Rotate the handwheel (11) until the fine adjuster

(17) touches the revolver depth stop (20).

• Set the measuring lens to a round figure (e.g. 0).

• Adjust the depth of cut using the handwheel (11)

and the measuring lens (12). The distance

between the top of the revolver depth stop and

the bottom of the fine adjuster is the adjusted

depth of cut.

• Tighten the clamping screw (15).

Triple depth adjustment using the revolver depth

stop (fig. E)

The revolver depth stop (20) can be used to set

3 different depths. This is particularly useful for deep

cuts, performed in steps.

• Place a depth template between the fine adjuster

(17) and the revolver depth stop (20) to adjust the

exact cutting depth.

• If required, set all three screws.

Make shallow cuts only!

Fine adjustment (fig. F)

When not using a depth template, or if the depth of

cut needs readjustment, it is recommended to use

the fine adjuster (17).

• Adjust the depth of cut using the fine adjuster (17).

One turn corresponds to approx. 1 mm.

• Read the depth of cut using the measuring lens (12)

and scale (13).

• Adapt the depth of cut to the millimeter using

the handwheel (11).

Depth adjustment with Router installed in inverted

position (fig. D)

• Remove the cap nut (27) and the knurled knob (9)

and replace it with the depth adjuster (DE6966)

available as an option.

• Connect the threaded rod of the new depth stop

to the threaded spindle (7).

• Set the depth of cut using the adjuster on the

new depth stop.

For installing the Router in inverted

position, refer to the relevant instruction

manual on the stationary tool.

Fitting the parallel fence (fig. A & G)

• Fit the guide rods (6) to the router base (21).

• Slide the parallel fence (19) over the rods.

• Tighten the locking bolts (5) temporarily.

Adjusting the parallel fence (fig. A & G)

• Draw a cutting line on the material.

• Lower the router carriage until the cutter is in

contact with the workpiece.

• Tighten the plunge lock (14) and limit the carriage

return using the knurled nut (9).

• Position the Router on the cutting line.

• Slide the parallel fence (19) against the workpiece

and tighten the locking bolts (5).

• Adjust the parallel fence using the fine adjuster (18).

The outer cutting edge of the cutter must

coincide with the cutting line.

• If required, loosen the screws (28) holding the

plastic guide strips (29) and adjust the strips to

obtain the desired guiding length.

Fitting the baseplate extension and trimming

plate (option) (fig. A & H)

When routing with large diameter cutters, it is

re-commended to fit the baseplate extension

(DE6268) (22) for secure handling. The trimming plate

(30) is used for trimming of projecting glued edges.

• Fit the baseplate extension to the free end of the

guide rods (6).

• Guide the tool with one hand on the knob (23)

and the other on the opposite grip (10).

• For trimming projecting glued edges, fit the

trimming plate (30) to the baseplate extension as

shown in figure H.

The trimming plate can be fitted directly next to the

cutter and ensures optimim guidance.

Fitting a guide bush (fig. J)

Together with a template, guide bushes (DE6430) play

a valuable part in cutting and shaping to a pattern.

• Fit the guide bush (31) to the router base (21)

using the screws (32) as shown.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW625E T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW625E T 4 Manual

Product: