546414

DeWalt DW625 T 6 Manual

32
Zoom out
Zoom in
Previous page
1/132
Next page
ENGLISH
30
Fine Adjustments (fi g. 6)
When not using a depth template, or if the depth of
cut needs readjustment, it is recommended to use
the fine adjuster (q).
1. Adjust the depth of cut using the fine
adjuster (q).
2. Read the depth of cut using the measuring lens
(l) and scale (m).
3. Adapt the depth of cut to the millimeter using
the handwheel (k).
Depth Adjustment with the Router
Installed in Inverted Position (fi g. 4)
1. Remove the cap nut (aa) and the knurled knob
(i) and replace it with the height adjusting tool
(DE6966) available as an option.
2. Screw the threaded end of the height adjusting
tool to the threaded spindle (g).
3. Set the depth of cut using the adjuster on the
height adjusting tool.
WARNING: For installing the router
in inverted position, refer to the relevant
instruction manual on the stationary tool.
Fitting the Parallel Fence (fi g. 1A, 7)
1. Fit the guide rod (f) to the router base (u).
2. Slide the parallel fence (s) over the rods.
3. Tighten the locking bolts (e) temporarily.
Adjusting the Parallel Fence
(fi g. 1A, 7)
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in
contact with the workpiece.
3. Tighten the plunge lock (n) and limit the carriage
return using the knurled nut (i).
4. Position the router on the cutting line.
5. Slide the parallel fence (s) against the workpiece
and tighten the locking bolts (e).
6. Adjust the parallel fence using the fine adjuster
(r). The outer cutting edge of the cutter must
coincide with the cutting line.
7. If required, loosen the screws (bb) and adjust
the strips (cc) to obtain the desired guiding
length.
Fitting the Baseplate Extension
(Option) (fi g. 1B, 8)
1. Fit the baseplate extension (v) to the free end of
the guide rods.
2. Guide the tool with one hand on the knob (w)
and the other on the opposite grip (j).
Fitting a Guide Bush (fi g. 9)
Together with a template, guide bushes play a
valuable part in cutting and shaping to a pattern.
• Fit the guide bush (ee) to the router base (u)
using the screws (ff) as shown.
Connecting a Dust Extractor
(fi g. 1A, 10)
The dust extraction adaptor consists of a main
section (hh), a cover (ii), a hose guide (jj), two screws
(kk) and two nuts (ll).
1. Slide the cover (ii) onto the main section (hh)
and let it click into place.
2. Connect a dust extractor hose to the dust
extraction adaptor.
3. Loosen the screw in the top of the router and fit
the hose guide (jj) as shown.
Prior to Operation
1. Check that the cutter is correctly installed in the
collet.
2. Set the cutting depth.
3. Connect a dust extractor.
4. Make sure the plunge limiter is always locked
before switiching on.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW625 T 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW625 T 6 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 8,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info