Manual DeWalt DW6141 (page 23 of 88) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546405

Zoom out

Zoom in

1/88

• Fit the guide bush (18) to the router base (11)

using the screws (19) as shown.

The screws (19) also hold the dust

extraction channel. Never operate the

router without this.

Connecting a dust extractor (fig. A)

Connect a dust extractor hose to the

dust extraction channel (9).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Always move your router as indicated in

fig. G (outer edges/inner edges).

Prior to operation:

• Check that the cutter is correctly installed in the

collet.

• Set the cutting depth.

• Connect a dust extractor.

• Always make sure the plunge limiter is locked

before switching ON.

Switching on and off (fig. A)

Switch the tool on using the on/off-switch (1).

• I = on. The tool now works continuously.

• O = off.

Loosen the plunge limiter and allow the

router carriage to regain its rest position

before switching off.

Using the guide bushes (fig. F)

• Secure the template to the workpiece using end

clamps.

• Select and install an appropriate guide bush (18).

• Subtract the diameter of the cutter from the outside

diameter of the guide bush and divide by 2. This will

indicate how much larger the template should be in

relation to the part being recessed.

If the workpiece is not thick enough,

place it on a piece of waste wood.

18 en - 5

ENGLISH

• Lower the router carriage until the cutter is in

contact with the workpiece.

• Tighten the plunge limiter (4).

• Set the exact depth of cut using the graduation (2)

or place a depth template between the depth stop

(3) and the revolver depth stop (6). The adjustment

range is indicated by the arrows (14).

• Tighten the depth stop locking bolt (5).

Triple depth adjustment

The revolver depth stop (6) can be used to set three

different depths. This is particularly useful for deep

cuts, performed in steps.

• Place a depth template between the depth stop (3)

and the revolver depth stop (6) to adjust the exact

cutting depth.

• If required, set all three screws.

Depth adjustment with router installed in inverted

position

• Set the depth of cut prior to installing the router

in inverted position.

For installing the router in inverted

position, refer to the relevant instruction

manual on the stationary tool.

A fine depth adjuster (DE6956) is

available as an accessory.

Fitting the parallel fence (fig. A & E)

• Fit the guide rods (15) to the router base (11).

• Tighten the locking bolts (10).

• Slide the parallel fence (16) over the rods.

• Tighten the locking bolts (17) temporarily.

Adjusting the parallel fence (fig. E)

• Draw a cutting line on the material.

• Lower the router carriage until the cutter is in

contact with the workpiece.

• Tighten the plunge limiter (4).

• Position the router on the cutting line. The outer

cutting edge of the cutter must coincide with the

cutting line.

• Slide the parallel fence (16) against the workpiece

and tighten the locking bolts (17).

Fitting a guide bush (fig. F)

Together with a template, guide bushes play a

valuable part in cutting and shaping to a pattern.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW6141 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW6141 Manual

Product: