544723

DeWalt DW518 T 2 Manual

29
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
27
Forward/reverse Slider (fi g. 4)
To select forward or reverse rotation, use the
forward/reverse-switch (c) (see arrow on tool).
WARNING: Always wait until the motor
has come to a complete standstill
before changing the direction of
rotation.
Two-gear Selector (fi g. 5)
Your tool is fitted with a two gear selector (d) to vary
the speed/torque ratio.
Release the variable speed switch and select the
required position. This can be done either with the
tool switched off or running under no load condition.
Always align the selector with the arrow on the gear
housing:
1 low speed/high torque (drilling large holes,
driving large screws)
2 high speed/low torque (drilling smaller holes,
drilling in wood)
For speed rates, refer to the technical data.
Do not change gears at full speed or during use.
Chuck Removal (fi g. 6, 7)
KEYED CHUCK
1. Open the chuck jaws as far as possible.
2. Insert a screwdriver into the chuck and remove
the chuck retaining screw (m) by turning
clockwise as shown.
3. Insert the chuck key (j) into one of the holes in the
side of the chuck and strike it with a hammer as
shown.
4. Hold the spindle with a spanner if necessary.
KEYLESS CHUCK
1. Open the chuck jaws as far as possible.
2. Insert a screwdriver into the chuck and remove
the chuck retaining screw (m) by turning
clockwise.
3. Tighten an hex key into the chuck and strike it
with a hammer as shown.
Prior to Operation
1. Insert the appropriate bit.
2. Mark the spot where the hole is to be drilled.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
Proper Hand Position (fi g. 1, 8)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (f), with the other hand on the main handle
(k).
Switching On and Off (fi g. 1)
T o run the tool, press the variable speed switch (a).
The pressure exerted on the variable speed switch
determines the tool speed.
Screwdriving
Select forward or reverse rotation.
Percussion Drilling (fi g. 1)
1. Select the percussion mode.
2. Press the switch (a).
If necessary, press the lock-on slide (b) upwards
for continuous operation and release the switch.
The lock-on slide works only in full speed, forward
rotation.
To stop the tool, release the switch.
To stop the tool in continuous operation, press the
switch briefly and release it. Always switch off the
tool when work is finished and before unplugging.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW518 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW518 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info