544723
28
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
26
Electronic Speed Control
The electronic speed control offers the following
advantages:
optimal tool control for accurate drilling
easier screwdriving
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Selecting the Operating Mode (fi g. 2)
The tool can be used in two operating modes:
Rotary drilling: for steel, wood and
plastics.
Percussion drilling: simultaneous rotating
and impacting for concrete and masonry
drilling operations.
Select the required operating mode by rotating the
mode selector (e) to the required position.
Inserting and Removing a Bit (fi g. 1)
KEYED CHUCK
1. Open the chuck by turning the sleeve (i)
counterclockwise and insert the bit shank.
2. Put the chuck key (j) into each hole in the side
of the chuck and turn clockwise until tight.
KEYLESS CHUCK
1. Open the chuck by turning the sleeve
counterclockwise and insert the bit shank.
2. Tighten firmly by turning the sleeve clockwise.
3. To remove the bit, proceed in reverse order.
Fitting the Side Handle (fi g. 1)
The side handle (f) can be fitted to suit both
RH- and LH-users.
WARNING: Always use the tool with
the side handle properly assembled.
1. L oosen the side handle.
For RH-users, slide the side handle clamp
over the 43 mm collar behind the chuck,
handle at the left.
For LH-users, slide the side handle clamp
over the 43 mm collar behind the chuck,
handle at the right.
2. Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fi g. 3)
1. Insert the required drill bit into the chuck.
2. Slacken the side handle (f).
3. Fit the depth adjustment rod (g) through the
hole in the side handle clamp.
4. Adjust the drilling depth as shown.
5. Tighten the side handle.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW518 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW518 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info