Manual DeWalt dw310k (page 27 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

382575

Zoom out

Zoom in

1/116

ENGLISH

Proper hand position requires one hand on the side

front grip (k), with the other hand on the back

handle (m).

Switching On and Off (ﬁ g. 1)

To run the tool, press the variable speed switch (a).

The pressure exerted on the variable speed switch

determines the tool speed.

To stop the tool, release the switch.

Always switch off the tool when work is finished and

before unplugging.

SETTING THE ELECTRONIC SAWING SPEED

(FIG. 1) - DW311

The speed control dial (b) can be used for advance

setting of the required range of speed.

Turn the electronic speed control dial to the required

level. The required setting depends on the thickness

and kind of material.

Use high speeds for sawing soft materials such as

wood. Use low speeds for sawing metal.

WARNING: After using the tool for

an extended period on low speed

settings, run it for approx. 3 minutes on

maximum no-load speed.

Cutting Wood

1. Clamp the workpiece securely and remove all

nails and metal objects.

2. Holding the tool with both hands, work with the

saw shoe pressed against the workpiece.

Plunge Cutting in Wood (ﬁ g. 5)

1. Rest the saw shoe on the workpiece in such

a position that the blade forms an appropriate

angle for the plunge cut.

2. Switch the tool on and slowly feed in the blade.

Make sure that the saw shoe remains in contact

with the workpiece at all times.

Pocket Cuts

1. Measure and mark the required pocket cut.

2. Using a narrow saw blade rest the bottom of

the saw shoe on the workpiece and make sure

that the blade is positioned on the cutting line.

If necessary, e.g. in confined spaces, use the

outer edge of the saw shoe as your guideline.

3. Switch on the tool and feed the blade into the

material at full speed, holding the tool firmly

against the workpiece.

Cutting Metal

When cutting thin metal always stabilize the

workpiece with wood on both sides. This guarantees

clean cuts and prevents damaging of the material.

For long, straight cuts draw a line on the workpiece.

Apply a thin film of lubricant along the cutting line,

switch on the tool and follow the cutting line.

Cutting Plastics

Always work at reduced speed. Carry out a test cut

to check whether the material is sensitive to heat.

Cutting Masonry

WARNING: When sawing asbestos

cement hazardous dust may be

produced. Follow the statutory

guidelines and observe the

recommendations issued by the

asbestos cement manufacturers.

Sawing Up to a Projecting Edge

(ﬁ g. 6)

Using a conventional blade installed upside down,

cut up to the projected edge.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Dust Extraction

When the tool is used indoor for extended periods

of time, use a suitable dust extractor designed in

compliance with the applicable Directives regarding

dust emission.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw310k in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 2,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw310k Manual

Product: