446500
29
Zoom out
Zoom in
Previous page
1/124
Next page
ENGLISH
27
WARNING: NEVER use a light socket.
NEVER connect the live (L) or
neutral (N) wires to the earth
pin marked E or
.
Using an extension cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm
2
; the maximum length is 30 m.
Assembly and adjustment
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only DEWALT battery
packs and chargers.
Battery pack (fi g. 1)
BATTERY TYPE
The DW052 and DW053 operate on 12 volt battery
packs. The DW054 and DW055 operate on 14.4 volt
battery packs. The DW056 and DW057 operate on
18 volt battery packs.
Charging the battery pack (fi g. 2)
When charging the battery pack (e) for the first time,
or after prolonged storage, it will only accept an
80% charge. After several charge and discharge
cycles, the battery pack will attain full capacity.
Always check the mains prior to charging the battery
pack. If the mains is functioning but the battery pack
does not charge, take your charger to an authorised
D
EWALT repair agent. Whilst charging, the charger
and the battery pack may become warm to touch.
This is a normal condition and does not indicate a
problem.
WARNING: Do not charge the battery
pack at ambient temperatures < 4 °C
or > 40 °C. Recommended charging
temperature: approx. 24 °C.
To charge the battery pack (e), insert it into the
charger (g) as shown and plug in the charger. Be
sure that the battery pack is fully seated in the
charger. The red charging indicator (h) will blink.
After approx. 1 hour, it will stop blinking and remain
on. The battery pack is now fully charged. The
battery pack can be removed at any time or left in
the connected charger for a longer period of time
(with a maximum of 14 days).
Inserting and removing the
battery pack
1. Insert the battery pack (e) into the grip until it
clicks in place.
2. To remove the battery pack, press the two
release buttons (f) simultaneously and pull the
pack out of the grip.
Battery cap (fi g. 2)
A protective battery cap (i) is supplied to cover the
contacts of a detached battery pack. Without the
protective cap in place, loose metal objects could
short circuit the contacts, causing a fire hazard and
damaging the battery pack.
1. Take off the protective battery cap (i) before
placing the battery pack (e) in the charger
or tool.
2. Place the protective cap over the contacts
immediately after removing the battery pack
from the charger or tool.
WARNING: Make sure the protective
battery cap is in place before storing or
carrying a detached battery pack.
Automatic refresh
The automatic refresh mode will equalize or balance
the individual cells in the battery pack at its peak
capacity. Battery packs should be refreshed
overnight after every 10th charge/discharge cycle
or whenever the pack no longer delivers the same
amount of work.
To refresh your battery pack, place it in the charger
as usual. The red light will blink continuously
indicating that the charge cycle has started.
When the 1-hour charge cycle has completed, the
light will stay on continuously and will no longer
blink. The battery pack is fully charged and can be
used at this time.
If the battery pack is left in the charger after the initial
1-hour charge, the charger will automatically initiate
the refresh mode. This mode will continue up to
8 hours, but the battery pack can be removed at
any time during the refresh mode.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too
hot or too cold, it automatically starts a Hot/Cold
Pack Delay, suspending charging until the battery
has reached an appropriate temperature. The
charger then automatically switches to the pack
charging mode. This feature ensures maximum
battery life. The red indicator blinks long, then short
while in the Hot/Cold Pack Delay mode.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW055 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW055 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 11,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info