Manual DeWalt DW 685 (page 29 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

78380

Zoom out

Zoom in

1/120

ENGLISH

Dust Extraction (ﬁ g. 10)

1. Insert the bolts (q) into the holes (r) in the

dust extraction adapter from the inside and

temporarily tighten the wing nuts (s).

2. Slide the adapter onto the dust extraction outlet.

3. Tighten the wing nuts.

4. Connect the dust extractor to the adapter.

5. Whenever possible, connect a dust extraction

device designed in accordance with the relevant

regulations regarding dust emission.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Proper Hand Position (ﬁ g. 8)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (y), with the other hand on the main grip (z).

Switching On and Off (ﬁ g. 1a)

1. To run the tool, press the On/Off switch (a).

2. To stop the tool, release the switch.

WARNING: Do not switch the tool

on or off when the blade touches the

workpiece or other materials.

Grooving

CUTTING GROOVES FOR

BISCUIT DOWELS (FIG. 5)

1. Adjust the cutting depth as described above.

2. Ensure that the star knob (f) is tightly fastened.

3. Guide the tool parallel to the workpiece.

GROOVING VENEERED AND EXOTIC WOOD PANELS

When grooving veneered and exotic wood panels,

use of the cutting insert is recommended to prevent

splintering (fig. 4).

1. Mount the cutting insert as described above.

2. Set the required cutting width.

3. Press the tool to a piece of soft wood and

carefully plunge the blade down through the

insert to produce a suitable slot in the insert.

USING THE PARALLEL FENCE (FIG. 1a)

The parallel fence is used to groove parallel to the

edge of the workpiece.

1. Mount the parallel fence as described above.

2. Set the parallel fence to the correct distance.

USING THE END MARKS (FIG. 7)

The end marks (k) are especially useful when

working on narrow workpieces and edges. The tool

is positioned by aligning the mark (k) with the edge

of the workpiece.

Scribing

PARALLEL SCRIBING (FIG. 8)

The DW685K is ideal for parallel scribing on wall and

ceiling panels.

1. For deeper cuts and for veneered panels, install

a 30-tooth TCT trimming blade.

2. Adjust the depth of cut.

3. Set the motor housing roughly parallel to the

surface of the workpiece.

4. Carefully guide the tool to perform the cut.

SCRIBING UP TO A CORNER (FIG. 1b, 9)

For optimum results and ease of use while scribing

up to a corner, proceed as follows:

1. Slacken the star knob (f).

2. Set the tool at a right angle to the base.

3. Tighten the star knob.

4. Press the rear edge of the tool base against the

wall or cornice and plunge the groover into the

workpiece.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW 685 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW 685 Manual

Product: