Manual DeWalt DW 621 (page 30 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

78334

Zoom out

Zoom in

1/132

ENGLISH

1. Adjust the depth of cut as described above.

2. Set the fine adjuster to zero using the ring (x).

3. Rotate the fine adjuster (q) to the required

position: one turn corresponds to approximately

1 mm and 1 mark to 0.1 mm.

Depth Adjustment with Router

INSTALLED IN INVERTED POSITION (FIG. 4)

1. Remove the depth stop (m) and replace it with

the depth stop (DE6956) available as an option.

2. Connect the threaded rod of the depth stop (m)

to the revolver depth stop (l).

3. Set the depth of cut using the adjuster on the

depth stop (m).

WARNING: For installing the router in

inverted position, refer to the relevant

instruction manual on the stationary tool.

Fitting the Parallel Fence (ﬁ g. 1, 5)

1. Fit the guide rods (e) to the router base (j).

2. Tighten the locking bolts (i).

3. Slide the parallel fence (h) over the rods.

4. Tighten the locking bolts (d) temporarily.

5. Remove the dust extraction adaptor (r) and

close the outlet using the dust extraction plug

(y) supplied with the tool.

Adjusting the Parallel Fence (ﬁ g. 6)

1. Draw a cutting line on the material.

2. Lower the router carriage until the cutter is in

contact with the workpiece.

3. Tighten the plunge limiter (o).

4. Position the router on the cutting line.

5. Slide the parallel fence (h) against the workpiece

and tighten the locking bolts (d).

6. Adjust the parallel fence (h) using the fine

adjuster (g). The outer cutting edge of the cutter

must coincide with the cutting line.

7. Firmly tighten the end lock (t).

Fitting a Guide Bush (ﬁ g. 7)

Together with a template, guide bushes play a

valuable part in cutting and shaping to a pattern.

– Fit the guide bush (z) to the router base (j) using

the screws (aa) as shown.

Connecting a Dust Extractor

(ﬁ g. 1, 5)

Connect a dust extractor hose to the dust extraction

adaptor (r) in the router carriage column or to the

dust extraction outlet in the parallel fence (f).

Prior to Operation

1. Check that the cutter is correctly installed in

the collet.

2. Select the optimal speed using the electronic

speed control dial.

3. Set the cutting depth.

4. Connect a dust extractor.

5. Make sure the plunge limiter is always locked

before switching on.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING: Always move your router as

indicated in figure 8 (outer edges/inner

edges).

Proper Hand Position (ﬁ g. 11)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on either

plunge limiter (o).

Switching On and Off (ﬁ g. 9)

The lock-on/lock-off switch (a) is located in the

handle on the right-hand side. The router is normally

locked in the off position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW 621 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 2,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW 621 Manual

Product: