Manual DeWalt dw 492 (page 22 of 79) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

390424

Zoom out

Zoom in

1/79

Fitting and removing a grinding wheel or cutting

disk (fig. D)

• Place the tool on a table, guard up.

• Fit the spacer (20) correctly onto the spindle (5).

• Place the grinding wheel or cutting disk on the

spacer.

• Screw the threaded flange (21) onto the spindle (5).

• Press the spindle lock (4) and rotate the grinding

wheel or cutting disk until it locks in position.

• Tighten the threaded flange (21) with the two-pin

spanner supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disk, loosen

the threaded flange (21) with the two-pin spanner.

Fitting a wire cup brush

• Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded flange.

Mounting the side handle (fig. E)

• For grinding, screw the side handle (6) tightly into

one of the holes (8) on either side of the gear case.

• For cutting, screw the side handle (6) tightly into

the top hole (7).

DW491K - Mounting the round handle (fig. F)

• Remove the side handle.

• Mount the round handle (22) using the two

screws (23).

• Fit one screw in the top hole (7) and the other in

one of the side holes (8).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disk.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the appropriate guard and disk or wheel.

Do not use excessively worn disks or wheels.

• Be sure the spacer and threaded flange are

mounted correctly.

• Make sure the disk or wheel rotates in the direction

of the arrows on the accessory and the tool.

Switching ON and OFF (fig. A)

The ON/OFF-switch of your Angle Grinder is

equipped with an unlocking switch or a locking switch

for continuous operation.

(U.K. & France only) - ON/OFF-switch (1) with

unlocking switch (2)

• To unlock the ON/OFF-switch, slide the unlocking

switch towards you.

• To run the tool, press the ON/OFF-switch.

• To stop the tool, release the ON/OFF-switch.

ON/OFF-switch (1) with locking switch (2a)

• To run the tool, press the ON/OFF-switch. The

tool now runs in continuous operation.

• To stop the tool, press the locking switch briefly,

and release the ON/OFF-switch.

Do not switch the tool ON or OFF when

under load.

DW491K - Using the Diamond guard (EZWS97)

(fig. C)

The Diamond guard is used for cutting concrete and

masonry, when accurate cutting depth adjustment or

dust extraction are required.

• Mount the Diamond guard as described above.

• Connect a dust extractor to the outlet (17).

• Set the cutting depth using the ruler knob in the

front plate (13).

• Observe the safety instructions applying

to diamond cutting disks.

• Use a suitable diamond cutting disk

(check the data of the manufacturer).

• The maximum rotation speed on the cutting

disk must not be lower than that of the tool.

• Do not use cutting disks with a diameter

exceeding 230 mm.

• Fire hazard! Do not use the dust

extractor when cutting metal!

• Make sure that the dust extractor used is

suitable for the material to be cut and the

Diamond guard can be connected.

en - 5

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw 492 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt dw 492

DeWalt dw 492 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish - 96 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw 492 Manual

Product: