Manual DeWalt DCMWSP564 (page 42 of 168) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

790949

Zoom out

Zoom in

1/168

ENGLISH

Protecting the Environment

wSeparate collection. Products and batteries marked

with this symbol must not be disposed of with

normal householdwaste.

Products and batteries contain materials that

can be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

ourenvironment:

• Run the battery pack down completely, then remove it from

thetool.

• Li‑Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Optional Accessories

WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DeWALT recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Release bail handle6 to turn mower off, let the blade come

to a stop and then remove the battery packs and safety key.

Clean out any clippings which may have accumulated on the

underside of the deck. Do not spray water or other liquids. After

several uses, check all exposed fasteners fortightness.

Cleaning

WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Lubrication

Your power tool requires no additionallubrication.

Blade Balancing (Fig. P)

Check balance of the blade33 by placing center hole in the

blade over a nail or round screwdriver36, clamped horizontally

in a vise35. If either end of the blade rotates downward, file

along the sharp edge of that dropping end. Blade is properly

balanced when neither enddrops.

• Sharpen cutting edges on both ends of blade, removing

equal amounts of material from bothends.

To Sharpen Blade in a Vise (Fig.O)

1. Be sure the bail handle is released, the blade has stopped

and safety key and battery packs are removed before

removing theblade.

2. Remove blade from mower. See instructions for Removing

and InstallingBlade.

3. Secure blade33 in a vise35.

4. Wear proper eye protection and gloves and be careful not

to cutyourself.

5. Carefully file the cutting edges of the blade with a fine tooth

file37 (not included) or sharpening stone (not included),

maintaining the angle of the original cuttingedge.

6. Check balance of blade. See instructions for BladeBalancing.

7. Replace blade on mower and tightensecurely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCMWSP564 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12.84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DCMWSP564 Manual

Product: