550344
40
Zoom out
Zoom in
Previous page
1/180
Next page
ENGLISH
38
Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
To install an accessory on the anvil, align the hole in
the side of the accessory with the detent pin (m) on
the anvil (l). Press the accessory on until the detent
pin engages in the hole. Depression of detent pin
may be necessary to aid installation of accessory.
To remove an accessory, depress the detent pin
through the hole and pull the accessory off.
Usage
Your impact tool generates the following maximum
torque:
Cat # Ft.-Lbs. In.-Lbs. Nm
DCF830 135 1620 185
DCF835 111 1330 150
DCF880 150 1800 203
DCF885 114 1400 155
CAUTION: Ensure fastener and/or
system will withstand the level of torque
generated by the tool. Excessive torque
may cause breakage and possible
personal injury.
1. Place the accessory on the fastener head. Keep
the tool pointed straight at the fastener.
2. Press switch to start operation. Release the
switch to stop operation. Always check torque
with a torque wrench, as the fastening torque is
affected by many factors including the following:
Voltage: Low voltage, due to a nearly
discharged battery, will reduce fastening
torque.
Accessory size: Failure to use the correct
accessory size will cause a reduction in
fastening torque.
Bolt Size: Larger bolt diameters generally
require higher fastening torque. Fastening
torque will also vary according to length,
grade, and torque coefficient.
Bolt: Ensure that all threads are free of rust
and other debris to allow proper fastening
torque.
Material: The type of material and surface
finish of the material will affect fastening
torque.
Fastening Time: Longer fasten ing time
results in increased fastening torque. Using
a longer fastening time than recom mended
could cause the fasteners to be overstressed,
stripped or damaged.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DCF835 T 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DCF835 T 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info